STAINLESS STEEL CYLINDER Piston seal ( Fig. 9 ) Mount with care not to twist the piston seal. Apply grease to the seal groove and outer circumference by rubbing grease into them as shown in Fig. 9. 3.Valve seal and Valve retaining gasket .( Air cushion type Mount them to the specified positions referring to Fig. 6.
AF ,AR , , , ,1 ISO VG32. 5 , 5 8 - 3-2. 1 B 1 3 3-3. 3-4. 9 - () 3-5. ,, (-)90 , 5.2 Nm A 10 - 3-6. ,,, RS2H5079Nm RS2H63801214Nm -5 3-7. M4 M41.5Nm -6 11 - 4. A GR-S-010(10g) -7 5. -8-9 -8 -9 12 - , 3 6. 6-1. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13 - / 6-2.
The auto switches may malfunction due to the interference from the magnetic fields. 9 - Pay attention to the length of time that a switch is ON at an intermediate stroke position.
Areas exposed to direct sunlight (ultraviolet rays). 9.Environment at an altitude of 1000 meters or higher. Heat dissipation and withstand voltage will decrease. Contact SMC for details. Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.
Proper use of the seal cap enables the enclosure to achieve IP67 specification. : Refer to page 33 for the seal cap. -12No.EX-OMN0009-G
If it is used in an environment where there is possible contact with oil, weld spatter, etc., exercise preventive measures. other than compressed air. 9. When the solenoid valve is mounted in a control panel or its 2. When there is a large amount of drainage.
The tightening torque of piping must be 1 Nm for M5 (This is equivalent to approximate 1/6 extra tightening after manual tightening.) and 7 to 9 Nm for R1/8 and NPT1/8. Exceeding this value can damage the piping. For piping of the Pressure switch, hold the piping with a spanner on the metal part of the piping (Piping attachment).
(page 9) F: Contents revised in several places. G: Contents revised in several places. H: Contents revised in several places. [July 2018] I: Contents revised in several places.
Refer to Fig. 4-1: Thrust force characteristics (P.9) and to Fig. 4-3: Allowable thrust force setting values (P.11) for details. Note 2) When mounted on a base with good heat dissipating capacity at 20oC ambient temperature. Note 3) The pushing force varies depending on the operating environment, pushing direction and table position. Refer to Fig. 4-1 Thrust force characteristics (P.9).
Maintenance 9 4. Basic Circuit for Cylinder Operation 9 5. Troubleshooting 10 S No. 2/10 Free Mount Cylinder / Series CU Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
The amount of grease per cylinder of 100 stroke is shown in attached table 9. Roughly, one scoop with a forefinger is approximately 3g.
. *3 The travel distance of the actuator per 1 pulse should be 10 [m/pulse]. 9 - [LECSC] LEJS40 LEJS63 LEJB40 LEJB63 Series Lead symbol H A B H A B T Lead 24 16 8 30 20 10 27 42 Parameter Para. No.
Note) For cable O.D. of 9 to 12 mm, remove the internal parts of the rubber seal before using.
Contact SMC in case it is necessary to hold a stopped position for an extended period. 9 3. Maintenance C a u t i o n When replacing seals, apply new grease for seals and then assemble. If the product is operated without applying grease, seals will be significantly worn and lead to air leakage at an early time. 3-1. Check 3-1-1.
MAXIMUM APPLICABLE FLOW RATE 9 7. TROUBLESHOOTING 9 8. CONSTRUCTION / PARTS LIST 10 9. SPECIFICATIONS OF BOWL ASSEMBLY 11-18 10. REPLACEMENT PROCEDURE 19-22 11. DISASSEMBLY DRAWING 23 12. DIMENSIONS 24 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Construction Fig. 9 Clamp cylinder construction No.
9 !8 @1 @0 !9 !8 @1 16 to 32 @0 !9 !8 @1 @0 !9 !8 @1 The numbers are the same as the "Construction" of the Best Pneumatics No.2 Series ZCUK. *BLUE links will lead to purchase pages. Seal Kit List Description Material Note No. Replacement Parts: Seal Kit Kit no.
7 w i t q A A @7 #3 @9 #0 #1#2 !8 !9 #4 @8 @6 !4 !5 Description Material Note Component Parts Description Material Note Component Parts No.
9 MSZAA (High precision type) $1 e $0 @7 @1 @9 !0 !2 #2 !6 !4 @4 #3 !8 #7 #8 o #6 q #9 y i $2 @3 @2 #1 @6 #4 #5 Component Parts Note Anodized Nickel plated Chromated Note No.
Description Material No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Material Note Note 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Rod cover Free-cutting steel Aluminum alloy Hard anodized Plug Cover Resin Aluminum alloy Hard anodized Wear ring Cylinder tube Carbon steel Aluminum alloy Hard anodized Pin Head cover Rolled steel Aluminum alloy Chromated Flat washer Piston rod Low carbon