Peltier-type Chiller Thermo-con/ Compact Type Normal In a moving car, normal conversation, or in a department store 60 dB In a car driving at high speed, in a noisy office, or the sound of cicadas (close distance) 70 dB Noisy On a running train, ambulance siren (close distance), or inside a pachinko parlor 80 dB 90 dB Very loud Karaoke bar (in the center) or the barking of a dog (close distance) Refrigerant-free Fluid contact material
This will cause a malfunction.
Flourinert is a trademark of 3M. GALDEN is a registered trademark of Solvay Solexis, Inc.
Low frequency operation In order to prevent malfunction, conduct a switching operation of a valve every 30 days. Also, in order to use it under the optimum state, conduct a regular inspection once a half year. 17-6-10
Grounding should never be connected to a water line, gas line or lightning rod. Multiple wiring is dangerous because it may lead to heat generation and cause a fire.
Through the use of a booster, a pressure that is higher than that of the main air passage can be supplied.
Male elbow: KRL Inch e l b a c i l p p A . D .
Direction Note) Values for 5 stations manifold with a 2 position single type valve.
Seal Tube Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0 MPa The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Body (White) O-ring Stud Effective when piping in a confined space. The body and the threaded portion can rotate. PAT.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
The ambient temperature range should be from 10 to 40C. Do not apply heat to the adsorption plate. This may result in a reduction in flatness. Storage Caution When mounting to equipment, use M5 hexagon socket head bolts, and fix the adsorption plate on a surface with a high degree of flatness.
In general, a mesh of about 50 to 100 is a guideline for the filter. When using ordinary tap water, scaling and sludge from substances in hard water such as calcium and magnesium can cause solenoid valves to malfunction. It is therefore necessary to install a water softener to remove such substances and a filter (strainer) immediately before the solenoid valve.
The product should be installed upright on a stable base. Do not install the product in a location where the air inlet and air outlet vents are blocked. Also do not use the product in a sealed enclosure. Do not use in an explosive atmosphere. Do not mount the product in a location where it can be exposed to prolonged sunlight. Use a protective cover.
Further more, conduct replacement using an IN, OUT differential pressure of 0.1MPa as a guide. 2) Start replacement after confirming that the temperature of the filter body is within a range of 0 to 40C. 3) When setting the element, be sure that it does not tilt inside the case. Adjust initial pressure drops to 0.01MPa to 0.02MPa or less. 6.
(See point A on the graph for series LJ1H30.)
Further more, conduct replacement using an IN, OUT differential pressure of 0.1MPa as a guide. 2) Start replacement after confirming that the temperature of the filter body is within a range of 0 to 40C. 3) When setting the element, be sure that it does not tilt inside the case. Adjust initial pressure drops to 0.01MPa to 0.02MPa or less. 6.
Can be used for a wide range of pressures from low vacuum up to a pressure of 1.0 MPa. The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Guide Collet Can be used in copper-free application. Body O-ring Flame resistance (Equivalent to UL-94 standard, material V-0) Stud Tube Effective when piping in a confined space.
Tightening of M3/M5 Threads 1) Tighten a barb fitting by hand, and give it an additional 1/6 turn with a wrench. 2) Tighten a barb elbow by hand, and give it an additional 1/3 turn with a wrench.
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
As a rule, this corresponds to two or three turns with a tool after tightening by hand. KQB2 KS KX Handling KM Caution KF 1. Store away from direct sunlight at 40C or less. 2. Open the inner package of double packaging in a clean room or other clean environment.