3 Do not use the cylinder under the following environments: An area in which fluids such as cutting oil splash on the piston rod An area in which foreign matter such as particles, cutting chips, or dust is present An area in which the ambient temperature exceeds the operating range An area exposed to direct sunlight An environment that poses the risk of corrosion 2.
If the allowable value is exceeded, an external cushioning mechanism such as an absorber needs to be installed. P. 305 Checking allowable load 5 M = 0.4 x 9.8 x 0.05 + 0.2 x 9.8 x 0.1 = 0.392 [Nm] If the allowable value is exceeded, an external bearing needs to be installed. Check if the load applied to the product is within the allowable range.
limit for intermediate stop using an external stopper, etc.
Small variations in flow rate depending on the number of knob rotations Stopper face AS-F AS-F TMH Contact face stopper ASD AS AS-FE Easier to insert and remove the tube KE AS-FG AS-FP AS-FM 17.1 mm 13.9 mm 12.2 mm AS-D 8.7 mm AS-T ASP AS-FS Series Current model AS-FS Series Current model Thread Part number Part number Thread Part number Part number Tubing diameter Tubing diameter ASN 6 4
It is necessary to use a solenoid valve with an electrical response time of 30 ms.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer. K Neoprene cross 110C * Standard Stroke * Maximum ambient temperature for the rod boot itself.
Page 527 * Please consult with SMC for non-standard strokes as they are produced as special orders.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 1. Be certain to connect the rod end to the load with the lock released.
As a reference, the tightening torque is 1 to 1.5 Nm. (When replacing the piping adapter ZS-46-N, tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm.
As a reference, the tightening torque is 1 to 1.5 Nm. (When replacing the piping adapter ZS-46-N, tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm.
46 x n + 29 L2 = 46 x n + 14 10 489 474 9 443 428 8 397 382 7 351 336 6 305 290 5 259 244 4 213 198 3 167 152 2 121 106 L L1 L2 S070 With mounting adaptor: VV317-02-1-02-A VQ 4-7 mounting hole P = 46 VKF VQZ VZ Manual override (Non-locking) VS DIN terminal facing upward 141.6 VFN Applicable cable O.D. 6 to 12 L Dimension n: Stations Stations Formula L1 = 46 x n + 89 L2 = 46 x n + 59 2 181
Especially in the case of small diameter pads. 6.When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to a workpiece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by the wind pressure.
An amplifying circuit and a dividing circuit are required to produce output which can be read by the counter, and these are attached to the cylinder case. The sensor head and amplifier section together are referred to as the sensor unit.
An amplifying circuit and a dividing circuit are required to produce output which can be read by the counter, and these are attached to the cylinder case. The sensor head and amplifier section together are referred to as the sensor unit.
Use the table below as a guide when adjusting auto switch positions, etc.
Use the table below as a guide when adjusting auto switch positions, etc.
As a reference, the tightening torque is 1 to 1.5 Nm. (When replacing the piping adapter ZS-46-N, tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
In an environment where vibration or impact occurs, provide an intermediate support even if the distance is within the allowable range in the graph. W L In case the product is installed on the ceiling, regard the mounting bolt pitch as L.
odd number, an even number that is one larger than this odd number is used for the calculation.