a n e l D i s p l a y a n d SigmaWin+TM 2.
L : Stroke [mm] V : Speed [mm/s] a1: Acceleration [mm/s2] a2: Deceleration [mm/s2] T1 and T3 can be obtained by the following equation. T1 = V/a1 = 300/3000 = 0.1 [s], T1 = V/a1 [s] T3 = V/a2 [s] T3 = V/a2 = 300/3000 = 0.1 [s] The acceleration and deceleration values have upper limits depending on the workpiece mass and the duty ratio.
Inch size 1/4" 1/8" 5/32" Flow rate (l/min(ANR)) 170 100 120 150 IN OUT Effective area (mm2) 2.6 1.5 1.8 2.3 IN P1 Note) Flow rate is the value measured under a pressure of 0.5 MPa and a temperature of 20C.
Switch for Vacuum Specifications) B C D J K P L W (without supply/release valve, without switch, pressure sensor) KJR KJRN L to L3 C to L3 06 P 560 56 P to J N 00 i Optional Specifications/Functions/Applications Note 19) Q 08 Type Function/Application Symbol Nil L to N A 07 ZK2 07 Without option B 10 09 Bracket P to N C to N With one bracket for mounting a single unit (Mounting screw is
) [mg/L] 50 or less p Standard item Acid consumption amount (at pH4.8) [mg/L] 50 or less p Total hardness [mg/L] 70 or less p Calcium hardness (CaCO3) [mg/L] 50 or less p Ionic state silica (SiO2) [mg/L] 30 or less p Iron (Fe) [mg/L] 0.3 or less p p Copper (Cu) [mg/L] 0.1 or less p Sulfide ion (S2) [mg/L] Should not be detected. p Ammonium ion (NH4+) [mg/L] 0.1 or less p Residual chlorine
215 Electric Actuator/Guide Rod LEYG Series p. 215 Electric Actuator/Slider LEF Series p. 31 Electric Slide Table LES/LESH Series p. 307 Electric Rotary Table LER Series p. 399 Electric Actuator/Miniature LEPY/LEPS Series p. 369 Electric Gripper (2-Finger Type, 3-Finger Type) LEH Series p. 425 * Order the actuator separately, including the actuator cable.
tubing P Effective area [mm2] Min. port size Release button dimensions L A2 M P Q O N Applicable tubing O.D.
How to Order S 2 B P H S4 200 LEY 63 A2 w y !0 i o e r t q u !1 !2 !3 !
VALVE TYPES AVAILABLE To operate a solenoid pilot valve in a vacuum s y s t e m , a s e p a r a t e p r e s s u r e s u p p l y m u s t b e s u p p l i e d t o t h e v a l v e t o m o v e t h e s p o o l o r p o p p e t a s d e s c r i b e d a b o v e .
Q1 = M L2 = L2 + (3 x P) 3. L1 + (3 x P) L2 + (3 x P) 4. L2 = Q2 = M L1 = 5. Q2 = M 6.
Shaft Pattern Sequencing I Applicable shaft type: S, W, Y How to Order F59 B C P D C S 50 90 X RA1 A2 A24 C10 -X6 Built-in magnet Auto switch Nil D None Built-in magnet Refer to page 11-7-13 for the part no. of auto switches.
Proof 65 3 Wire Output PNP 25 3 Wire Output NPN 26 3 Wire Analog Output P I P I N G S P E C I F I C AT I O N S 01 Direct Piping 1/8 PT T1 NPTF 1/8 H O W T O O R D E R P O S I T I V E P R E S S U R E S W I T C H S E R I E S ISE4 ISE4 B D W I R I N G S P E C I F I C AT I O N S O P E R AT I N G P R E S S U R E L Grommet Entry 3m Lead 0.6m -0.1 ~ 1MPa L -10 ~ 100KPa DIN R A I L M O U N T I N
O K L XA, depth XB J Q MHC NB M MHT G I NA 3-UA thread depth UB P .C.D.R (Mounting thread) 3-SA, counterbore dia.
Controller Set Up (P.42) and 14. Card Motor Controller Configuration software (P. 70) for instructions on how to setup. (7) Test operation Refer to section 10. Monitor and Test Mode of the Controller (P.50) and 14.5 Monitor/Test window (P. 80) for instructions on operating instruction of test operation 14 - 3.
P = Thread pitch M3 x 0.5; M4 x 0.7; M5 x 0.8; M6 x 1 Enter the desired figures in the portion of the diagram. XA1 to XA24 are the standard products that have been additionally machined. Chamfer face of the parts machining additionally is C0.5. CRB2 2. CRBU2 L1 + (3 x P) L1 + (3 x P) Q1 = M Q1 = M 3. CRB1 L2 + (3 x P) L2 + (3 x P) 4. MSU L1 = L1 = L2 = L2 = CRJ 5.
8 x L counter bore J J A + Stroke M M Rod end male thread CHKDB20, 25 CHKDB32 to 100 Water resistant type S N g C B + Stroke h + Stroke A + Stroke Rod end male thread (mm) B C D E F G H J K L M P Q R A Bore size (mm) 20 51 43 8 12 10 M8 x 1.25 10 6 30 5.5 9.5 depth 5.4 43 1/8 16.5 6 25 53 45 8 14 12 M10 x 1.5 12 6 36 5.5 9.5 depth 5.4 49 1/8 17 8 32 61 51 10 18 14 M12 x 1.75 15 7 47 6.6
Bracket mounting inserts found on the standard ISE20B are omitted as well. 25A-ISE20B is UL/CSA, CE and RoHS compliant, with an IP65 enclosure rating.
Bracket mounting inserts found on the standard ISE20B are omitted as well. 25A-ISE20B is UL/CSA, CE and RoHS compliant, with an IP65 enclosure rating.