Step Motor Controller (Servo / 24 VDC) (Step No. 2) [Normal mode] Step data example Moving Move Accele Decele Pushing T rigger Pushing No Speed Position Area1 Area2 In position force ment MOD ration ration force L V speed mm/s . mm/s mm mm mm mm % mm/s2 mm/s2 % % 0 1 Absolute 100 50.00 1000 1000 0 0 0 100 0 0 0.1 2 Relative 50 10.00 1000 1000 0 0 0 100 0 0 0.1 Flow chart (example) Controller Parallel I/O signal (1) Select/ input
(at 25C water) Temperature characteristics 5% F.S. (0 to 50C, based on 25C) Pulse output, N channel, open drain, output for monitor unit PF2D 300/301 (Specifications: Maximum load current of 10 mA; Maximum applied voltage of 30 V) Pulse output Output Voltage output Note 5) 1 to 5 V Accuracy: 2% F.S., Min. load impedance: 100 k (Output impedance: 1 k) Analog specifications Current output Note
switch Reed switch 12 V Relay PLC Grommet 24 V Yes 5 V, 12 V IC circuit Diagnostic indication (2-color indication) 12 V 5 V A96V A96 IC circuit Yes Grommet A93V A90V A93 A90 100 V Relay PLC 12 V 24 V 2-wire No 100 V or less IC circuit Solid state auto switches marked with are produced upon receipt of order.
or less (with load current of 80 mA) (PF2D300) Maximum applied voltage: 30 V 2 outputs Environmental resistance Note 4) Output specifications Switch output PNP open collector Maximum load current: 80 mA Internal voltage drop: 1.5 V or less (with load current of 80 mA) (PF2D301) 2 outputs NPN open collector or PNP open collector (same as switch output) Accumulated pulse output IP40 Enclosure
Female lhread length {"1') is shonerfor the lollowing . 2o0 (2') 1/g & 1A st. 1/s & 1/a st. r/s & 1/a st. l=o.44 25O (2112')' I/s st. r/s st. '/s stl=0.44 300 (3") ]/s & 1/a st. 1/e &r/l st. 1/e & 1A st. 400 (4) 1/s &1/a st. r/s & 1/a st. 1/e &14 st. Series NCQT Dimensions Spring Extend NCQTBO-OT T Type Bore,, 9t4,F' I 60re ,b,:!
Female lhread length {"1') is shonerfor the lollowing . 2o0 (2') 1/g & 1A st. 1/s & 1/a st. r/s & 1/a st. l=o.44 25O (2112')' I/s st. r/s st. '/s stl=0.44 300 (3") ]/s & 1/a st. 1/e &r/l st. 1/e & 1A st. 400 (4) 1/s &1/a st. r/s & 1/a st. 1/e &14 st. Series NCQT Dimensions Spring Extend NCQTBO-OT T Type Bore,, 9t4,F' I 60re ,b,:!
Vacuum pressure Theoretical lifting force Horizontal lifting force [N]Safety factor 1/4 [kPa] [N] 1 cup gripping -50 40.2 10.0 2 cups gripping -67 53.8 13.4 3 cups gripping -73 58.7 14.6 (Calculated by W = P X S, S = r2, r = 32 / 2. Refer to 3.3 How to calculate theoretical lifting force for the detail.)
TQ1230001-OM102-B 6.2 Change to 1 cup (without flange) *No mesh in the vacuum (V) port. If the mesh is necessary in the vacuum (V) port, use the vacuum gripper with cup mounting flange. 1. Removal of the cup mounting flange (1) Loosen the bolt (M6 x 10), then remove the cup mounting flange. Be careful not to lose the O-ring. (2) Remove the parallel pin. 2.
Table (1) Allowable Kinetic Energy At Piston Impact Unit: [J] Allowable kinetic energy 50 to 500mm/s 20 25 32 40 50 63 80 100 Piston speed 0.055 0.09 0.15 0.26 0.46 0.77 1.30 2.27 7-7-19
Wherein; Maximum detectable piston speed = V [mm/s] [mm] switch Auto of range Operating [mm/s] V = 1000 [ms] load of time Operating Design the product to prevent reverse current when the circuit is opened or the product is forced to operate for operational check. Reverse current can cause malfunction or damage to the product. Reserve a space for maintenance.
S S S S [Measurement mode] Measurement mode is the condition where the flow is detected and displayed, and the switch function is operating. This is the basic mode; other modes should be selected for set-point changes and other function settings. F0 function setting F1 function setting F99 function setting Do not use the product for flammable fluid. Fire or explosion can result.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) : The analogue input update time can also be set for every Wireless Remote unit. Refer to "Remote setting" (page 38). DA refresh time -26No.EX-OMV0017-C (4) Remote registration Registration for wireless communication between the Wireless Base unit and the Wireless Remote unit.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
Model Note Accessory/Option FH34 0 1 CB-48H Petroleum, Water-glycol, Emulsion to CB-48H-V Phosphoric ester FH44 0 1 Differential pressure indicator CB-52H Petroleum, Water-glycol, Emulsion FH342 CB-52H-V Phosphoric ester FH54 0 1 CB-64H Petroleum, Water-glycol, Emulsion to CB-64H-V Phosphoric ester FH64 0 1 FH34 0 1 CB-49H Petroleum, Water-glycol, Emulsion to CB-49H-V Phosphoric ester FH44
Where the maximum detectable piston speed = V (mm/s) Travel of auto switch (mm) V (mm/s) = X1000 Change over time of load (ms) Reserve a space for maintenance. Remember to leave space for maintenance when installing the product. Product handling Installation Follow the specified tightening torque.
Output deviation factor (% F .S.) 0.6 0.5 0.4 Return 0.2 0 0 0.2 0.4 0.5 Out 0.6 0.8 0 25 50 75 1 1 2 3 4 1 5 100 Input signal (%F .S.)
[s] [mm] [mm] 1.5 64 100 kPa 0.15 mm 2.0 64 100 kPa 0.3 mm [s] [s] [mm] [mm] -21No.PS-OMF0005CN-E ISA2-G ISA2-H 100 kPa 1.5 64 5 m 100 kPa 2.0 64 5 m [mm] [mm] [kPa] [kPa] -22No.PS-OMF0005CN-E ISA2 () 1 ON ( +)ON ()ON OFF Yes 2 No ( OFF +)ON 1 ()ON 3 ()ON 1,3 OFF 4 5 ON OFF 6 7 8 -23No.PS-OMF0005CN-E No.