PF2x7.eng A fire or explosion can result. 4 Set value Set value or 3 4 or 3 180 0 Switch operation (OUT2) Set value is calculated and set. SET U P DOWN DOWN U P DOWN Outline of setting Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
L m3 m3103 L ... 1: Hysteresis can be set between "0" and "3% of maximum rated flow". If the difference between Set point 1 and Set point 2 is less than "6% of maximum rated flow", the maximum Set value of hysteresis is (Set point 1 Set point 2) divided by 2. 2: When Set point 1 = Set point 2, chattering may occur.
The fluid temperature range is 0 to 50 oC. Before designing piping confirm the pressure loss at the sensor from the pressure loss graph. Confirm pressure loss of the sensor from the characteristics data. Do not use compressed air containing a lot of condensate. Insufficient air quality can cause operating failure.
In measurement mode, when the button is pressed for 2 seconds or longer, [F 0] is displayed. Mounting by panel mount adapter Fix the panel mount adapter to the controller by the mounting screws M3 x 8 L (2 pcs.).
Relation between Peak Pressure and Relation between Peak Pressure and Upstream side tube Upstream side tube (supply pressure 0.5MPa, volume 50cc) (supply pressure 0.5MPa, volume 100cc) TU1208 tube TU1610 tube TU1208 tube TU1610 tube T1613 tube Normal air blow T1613 tube Normal air blow 0.25 0.25 Peak Pressure [MPa] Peak Pressure MPa 0.2 0.2 0.15 0.15 0.1 0.1 0.05 0.05 0 0 10mm 50mm 10mm 50mm
2.5 Hz 3.2 Hz 3.6 Hz 4.4 Hz 0 2 4 6 8 7 Number of rotation of OFF adjustment needle 24% 58% 69% 67% ON At an inlet pressure of 0.3MPa.
Switch No. 0 (Default) 1 2 3 4 5 6 7 8 9 Slower (Speeds up gradually.)
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
Rotation angle rad Inertia moment kgm For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. ) 1 ( ) 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
0.88 6 3 +0.02 0 6 M(D)HR3-15 9 !
WaitTime_Setting int 500 WaitTime setting after valve operation (Unit: ms, Range: 0..1000ms) It is a wait time value after the valve for opening gripper is energized. Set an appropriate value according to the opening speed of the gripper by adjusting the opening of the metering valve.
On-stream: 2 ~ 40oC Spaces needed for maintenance Storage: 0 ~ 50oC (when there is no drain Front : 600 mm water inside of the piping) Rear : 600 mm Top : 600 mm Locations where temperature changes rapidly.
Set value Alarm type Operation profile 0 No alarm 3 Upper limit of the * Even if PV is in the alarm triggering range when power is supplied, the alarms above do not generate an alarm immediately.
Locations where ambient temperature is beyond following range: On-stream: 2 ~ 40oC Storage: 0 ~ 50oC (when there is no drain water inside of the piping) Locations where temperature changes rapidly.
(Figure b) : Bit status "0" and "1" on a data corresponds solenoid valve status ON and OFF (0: OFF, 1: ON), and output number starts at zero from LSB (least significant bit). -15No.EX-OMO0007-E Troubleshooting and Maintenance Troubleshooting Chart Applicable SI unit: EX180-SMJ3/5 When any malfunction is observed, perform the following troubleshooting.
/size 750W80 Type of Motor AC servo motor (100/200VAC) Encoder Absolute 22bit encoder (Resolution: 4194304 p/rev) (Driver type: LECSC-T) Absolute 18bit encoder (Resolution: 262144 p/rev) Power consumption [W] Note 10) 1,100 (Maximum power) Type Note 11) Non-magnetizing lock specifications Lock unit Holding force [N] 5,700 3,400 1,200 Power consumption [W] at 20 10 Rated voltage [V] DC24 0-
(Tightening torque 0.6 to 0.8Nm) Dipswitch ON 1 2 3 4 5 6 7 8 9 10 Enable or disable of Dip switch MAC ID Baud rate HOLD/CLEAR Setting at the time of shipment 1 2 3 4 5 6 7 8 9 10 Node address: 0 Baud rate: 125kbps Hold/Clear: Clear Dip switch: enable 8 - Setting of MAC ID MAC ID 1 2 3 4 5 6 0 OFF OFF OFF OFF OFF OFF 1 OFF OFF OFF OFF OFF ON 2 OFF OFF OFF OFF ON OFF : : : : : : : 62 ON ON
When bit data (RY0F) is 0, it is set immediately before communication abnormality. Setting of terminating resistor This switch is selected to terminating resistor enable or disable.