IS3000 Do not use in an environment, where water or oil is splashed. Because it is the open type construction. If water or oil were to make an ingress, the electrical circuit would be corroded and result in a malfunction or damage. 2. Operating fluids are either air or inert gas exclusively. Never use liquids. 3. Never use in an environment where flammable fluid or gas is used.
Therefore, do not operate it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). 2.
Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) Set point ON When assembling the connector to the switch housing, push the connector straight onto the pins until the lever locks into the housing slot.
The silencer's response properties do not change in the initial stage, but will change due to the blockage after long use. Replace it after using about 500,000 times. This number is subject to change based on fluid quality and energization time. 2. When using a silencer, make space for silencer replacement. 1.The controller starts its output the moment the power switch is turned ON.
If even one of the cups do not seal, there can be a loss of pressure to all cups. SMC addresses this problem with series INO Self Sealing Vacuum Cups. By utilizing a small mechanical check valve, it only opens when the cup comes in contact with a part. This will maintain system vacuum pressure if one part is absent.
style cannot be mounted on the same manifold. 02 2 stations 1 2 3 Stations Uside Dside 3m 18 18 stations VVQ100-10A-1 Electrical entry Multi-connector C Connector location U S Top entry Side entry Cable length 0 1 2 3 Without cable With cable (1.5m) With cable (3m) With cable (5m) Option None DIN rail mounted (With standard length of DIN rail) DIN rail mounted (Without DIN rail) D DO
SYJ W Non-locking push style (Flush) SX VK Note: To avoid contact failure and broken wires, do not pull out the lead wire with excessive force.
When generating a vacuum, do not reduce below 700Torr. 2. The gas permeation through the O-ring (FKM) seal is minute at normal temperatures, but there is a marked increase at high temperatures. Take special precautions against leaks and permeation at high temperatures. 3.
Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-2 3 Air Suction Filter Series ZFA 100 200 Dimensions: ZFA Single unit Bracket ZX ZR Cover opened-up dimensions 70 Element extracted dimensions 55 ZM ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800)
Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-5 3 Series ZFB Dimensions Element Replacement 1. Stop the operation and reduce the internal pressure of the filter to atmospheric pressure. 2.
Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirt's deformation range. Positioning should be performed accurately.
Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range. Positioning should be performed accurately. Especially in the case of small diameter pads. 6.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
(Do not cut the tube with plier6, nippers, scissors, utilitv knife, etc.) ePull out the tube while keeping the release button depressed. lJf the release butlon is nol held down, the tube cannot be withdrawn.) OGrasp the tube, then slowly push it until il comes lo a dead-end.
Do not attempt to disassemble tublng lrom fitting with vehicle air system under pressure, Glnflhd hhftilco ffiilt hr:iffi,bJn-|d$u[,ru,fl OHighly sistrrt OGradually corro&s (clpends on oporating conditions) Vl,lodelEl8ly .onodes (depends on opelating conditions) Not r6commnd6d br high concnlcrlions & )posur l coraoded Body Stud Guide Body Chuck Releass Bushing Collet Oring Packing SMC For
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
swirches Pfessrre to the side irdicated by label B rotales the shaft clockwise, pressu to the side hbeled A rciates the shaft countercl@kwise, l{cnAtB\lv3o l,rcRAroso--10() o Series:NCRAl Shaft Load fr"u lvlc&l direclion Fsa Fsb $cRAAUrgt 6 cnAtaso 110 44 44 NcRAlffl 132 44 ffi NCf,Ant8() 198 44 NCnA1otOO 220 44 In the stop position, the load can meet the value given in lhe list, please do