PAB-OM-C007-B When installing piping or a fitting into a port, ensure that sealant material and cutting chips of threads do not enter piping. When using sealant tape, leave the first 2 threads exposed at the end of piping /fitting. T ightening torque Undertightening causes liquid or air leakage w hile overtightening causes breakage of threads and other parts.
IP65() 4.57()JIS C 3306 0.51.5mm 22 ,3 O JIS C2805 R1.25-3 Y () 1.25-3 2.53.7 0.290.35Nm () 4 4 4 4 5 5 5 5 (3 ) 0.50.6Nm 2 () 2 () 1 () 1 () 4() 3() 4() 3() 5() 4 5 DC AC DC AC SGC SGH AC 9 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series/ / / / DIN DIN DIN DIN AC DC DIN IP65() ( ( ( ( ) ) ) ) (4.5~7) IP65() NL:,R: LED:,R: V: V: 180 AC DIN (DO
Do not use Use in combination with the DI Filter Set (HRS-DP001) is not possible. to tighten the case. resin filter case (1)). After mounting the particle filter bracket, tighten the M5 screws on the back of the thermo-chiller panel.
Do not use to tighten the case.
Do not use to tighten the case. * When using the filter, the supply pressure should be 0.69 MPa (100 psi) or lower. Please replace the element when the pressure drop of this product reaches 0.15MPa. For replacement of the element, confirm the pressure inside the filter is zero, and refer to mounting procedure 3) and 4). 2.
Do not turn off the power supply before the storage completion message is received.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not disassemble the product. , as this could allow contact with any residual chemicals. 1) The product does not operate when power is applied. The product creates suction, but does not dispense. There is no suction. Countermeasures Warning 2) Pump operates, but does not dispense. Operating frequency is too high. The frequency should be set at or below the maximum operating frequency.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Note 1) Do not turn the pressure adjustment set needle excessively counterclockwise to prevent the cylinder from suddenly extending. ASN AQ ASV AK ASS ASR ASF 15-15-5
Do not plug or tighten it. (P port) (A port) (R port) 5-5-11 2 Series VGA342 Made to Order Specifications: Please contact SMC for detailed specifications, dimensions and delivery.
To prevent malfunctions, do not clog the breathing port. (When mounted on a metal surface, breathing air can go through from the breathing port to the breathing groove; however, when the valve is mounted on a rubber surface, the breathing air may be blocked by the deformation of rubber.) 2.
Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
Do not supply air pressure from other ports than 1(P) port. Air leakage may occur when the pressure is supplied from other ports. 1. Ensure connection so that air is supplied to the port 1(P) port. Air leakage may occur when the pressure is supplied from other ports. 2.
120 VAC (50/60 Hz) 4 220 VAC, 50/60 Hz 5 24 VDC 6 12 VDC 7 240 VAC, 50/60 Hz 9 Other Option Option Non-locking push type (Flush) Non-locking push type (Extended) Locking type (Tool required) Locking type (Lever) Nil For VFS130 G GS Grommet Grommet with surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor D DZ DIN terminal Common pilot exhaust 22 A B DO
flange Head flange Single clevis Double clevis Center trunnion Change of rod end shape Heat resistant cylinder (150C) Rod end nut Clevis pin With heavy duty scraper Standard Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel -XC7 Piston rod ball joint Rod clevis Rod boot Option -XC10 -XC11 -XC22 -XC35 Dual stroke cylinder/Double rod type Dual stroke cylinder/Single rod type Do