Size: 1/8, Thread: NPT, Port Size: 1/8, Accessory: None, Option 1: Drain Cock, Option 2: CRZ [Bowl Guard(Size2000 Only)+Flow Direction:Right->Left+Name Plate Caution on Bowl]
Size: 1/8, Thread: NPT, Port Size: 1/8, Accessory: None, Option 1: 36 [Drain Cock+Nylon Bowl (Including Sight Dome)], Option 2: Name Plate, Caution on Bowl
CRB2/CRBU2/CRB1 Single vane type Double vane type 90, 100 270 180 90 Chamfer 0 5 +4 0 o n ti o n ti a a 0 r r t t 9 a a o o n n R R e +4 0 g g g 0 e e n 0 a 2 1 0 1 r 7 8 9 n 0 0 e o e g ti +4 0 +4 0 g n a n a t a o r r R n n o o ti ti a a t o t o R R Chamfer A port B port Chamfer Chamfer B port A port A port B port A port B port For size 40 actuators, a parallel keyway will be used instead
valve (A) (A) 4 (B) 2 (A) 4 (B) 2 Note) A 1 5 (R1) 3 (R2) 1 (P) 3 (R2) 5 (R1) 1 (P) N.C.
P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.
SUP block plate VVQ2000-16A EXH block plate VVQ2000-19A Port plug Note 1) A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B C4 (N3) With 4 (5/32") One-touch fitting Side port Cylinder port sizes Fill out in case of mixed sizes (CM/LM/NM).
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
B A HS 056 HS B A B A 075, 106 HS B A B A 150, 200, 250 Note 1) Figures in the table below are references for auto switch mounting positions in the stroke end detection.
Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.
When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Mineral oil A C A A A A 18 Sodium hypochlorite (2%, Room temperature) A C A D D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B A D A B 23 Unless noted otherwise, the solution concentration is in a saturated state.
Operate the piston within a range such that collision damage will not occur at the stroke end. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer.
The solenoid must be connected to a safety barrier located in a non-hazardous area.
Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.