EX500 to D) Supply voltage 24 VDC Supply current Max. 2.8 A (Max. 0.7 A per branch) Number of outputs 64 points (16 points x 4 branches) Connection output device The EX500 series SI unit manifold (connection from communication port A to D) Supply voltage 24 VDC EX Supply current Max. 3.0 A (Max. 0.75 A per branch) Branch cable length 5 m or less between connected devices (total extension 10 m or
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Please consult with SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire. Please consult with SMC regarding use in this kind of environment. 15-17-8
M Applicable tubing b Applicable tube a B A Reducer: M-32R-2, M-04R-2 Applicable tubing O.D. x I.D.
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
IDX-OM-W020-C / Series IDFB3E-11 -A,S IDFB4E-11 -A,R,T,S,V IDFB6E-11 -A,K,R,T,S,V IDFB8E-11 -A,K,R,T,S,V IDFB11E-11 -A,K,R,T,S,V IDFB15E-11 -K,R,T,S,V URLhttps://www.smcworld.com/ English instruction manual can be downloaded from our URLhttps://www.smcworld.com/ SMC () * 1 ) JIS B8370 * 2 ) ISO4414 *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems
Cover Cover Turn counterclockwise Turn counterclockwise Pull Pull F.R.L. (2) Use a flat head screwdriver (with a 2.9 mm blade width) to set the (green) limit indicator. Be careful not to bend the other needle or damage the dial plate. (2) Use a flat head screwdriver (with a 2.9 mm blade width) to set the (green) limit indicator.
M Applicable tubing b Applicable tube a B A Reducer: M-32R-2, M-04R-2 Applicable tubing O.D. x I.D.
Use display of label attached to the sensors as a guide. Approx. 50 mm Distance measurement BEST DETECTING POSITION 50mm Detection hole Detection area 7. The measurement of a part with a high-charge potential can be highly dangerous as it can cause a discharge to the users hand.
Fluid Standard specifications Option Note) Water (Standard, up to 40C) Air (Standard, Dry) Turbine oil Vacuum (up to 1.3 x 102 Pa) Carbon dioxide (CO2), Nitrogen gas (N2) Vacuum (up to 1.3 x 10-1 Pa) (V, M) Non-leak (106 Pam3/s or less) (V, M) JIS Symbol A C.O.
The minimum bending radius indicates the value at which the tubing will fold at a temperature of 20C. At higher temperatures, the tubing may fold at more than the minimum bending radius. 4. Store away from direct sunlight in a location at no more than 40C. 1981-2000 Reprint May 2000 6
Calibration is easy with auto-preset function. 4 Installation of a group of sensors as a manifold style at the same site 3 Adsorption confirmation of a workpiece absorbed with water/oil Series ZSE50 Series PSE54 16-3-23 16-2-28 Adoption of a stainless diaphram enables to detect, even though water or oil is adhered to a workpiece and then made ingress to the sensing part.
HRS012-A-10 HRS012-W-10 HRS018-A-10 HRS018-W-10 Model Air-cooled refrigeration Water-cooled refrigeration Air-cooled refrigeration Water-cooled refrigeration Cooling method Refrigerant Control method Ambient temperature/humidity Note 2) R407C (HFC) PID control Temperature: 5 to 40C, Humidity: 30 to 70% Clear water, 15% ethylene glycol aqueous solution Note 5) Circulating fluid Note 3) Circulating
It is recommended for future piping expansion that all piping ends should terminate with a T joint with plugs.
Going to Great Lengths with Polyurethane Tubing L G O B A S L N O P I R T O U D L O U S C T L S A B O G L Polyurethane Tubing Series TIUB & TU SMC Offers a Rainbow of Tubing Types, Colors, Sizes and Lengths Polyurethane has 8 Quick Ship colors, equalling 336 part numbers, stocked on the shelf and ready to ship in all available sizes and lengths.
Description Note 1 +15 V 1 2 1 2 5 2 Output signal 1 D-F8N 3 4 3 4 Display part 3 GND Socket connector A-coded (Normal key) Plug connector A-coded (Normal key) 4 Output signal 2 D-F8N DD1677
(mm) 5 6.5 4 8 2.5 Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually. Measure 2R when the tube breaks or is crushed.