ITV Note 5) When mounting a blanking plate and the regulator with different pressure set, please inform SMC of the order of a manifold station beside a purchase order. Note) Refer to the table below for possible mixed combination.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
Amount of displacement on A when the load is applied at F. Amount of displacement on A when the load is applied at F.
set of a and b in the figures. wBJ3-1: A set of c, d and e in the figures.
set of a and b in the figures. wBJ3-1: A set of c, d and e in the figures.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
Normal In a moving car, normal conversation, or in a department store 60 dB In a car driving at high speed, in a noisy office, or the sound of cicadas (close distance) 70 dB Noisy On a running train, ambulance siren (close distance), or inside a pachinko parlor 80 dB 90 dB Very loud Karaoke bar (in the center) or the barking of a dog (close distance) Refrigerant-free Fluid contact material
Material HNBR: Nitrile hydride rubber 500 700 500 1000 1500 800 1000 1200 1000 500 Flow rate Q l/min (ANR) Viewing the graph The sonic range pressure to generate a flow rate of 500l/min (ANR) is P = 0.64MPa for a 3 orifice, and P = 0.35MPa for a 4 orifice.
A A B (mm) D-A9V D-A9 D-M9 D-M9W D-M9V D-M9WV A B A B Bore size (mm) W Hs A B W A B Hs 32 40 50 63 12 [17] 9 1 12 [17] 9 29 8 [13] 5 3 (0.5) 8 [13] 5 27 16 11.5 1.5 16 11.5 32.5 12 7.5 5.5 (3) 12 7.5 30.5 14 <19> 14.5 4.5 14 <19> 14.5 42 10 <15> 10.5 8.5 (6) 10 <15> 10.5 36.5 16.5 17.5 7.5 16.5 17.5 42 12.5 13.5 11.5 (9) 12.5 13.5 40 [ ]: Values for 5 mm stroke with 32 < >: Values for 10
2%4$2$4$5 @4 #0 Section A-A' 20A Data A' $0 $1 #4 #5 #2 @1 $6 $3 Component Parts No. Description Cam follower cap Magnet Magnet Seal magnet Rail End spacer Square nut Square nut Spring pin Parallel pin No.
B A 32 6 7 7 8 40 11 13 12 14 Aim at this number.
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
(When port sizes for A, B ports are mixed, indicate C4 or C6 in cell .)
19.5 24.5 30 37 6 7 9 10.5 14 16.5 1.0 Allowable moment coefficient 0.7 0.5 Note) For A, A, A and A, there is no difference in the corrected values due to the stroke.
Please note that the graph should only be used as a guide, as there is a tolerance of about 10% in the clamp cylinder body.
at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
Contact SMC if a stopper cylinder is to be used for stopping a load that is connected directly to a cylinder, as this will cause the cylinder's thrust to act as a horizontal load.
A spring washer will be required separately for VP470.
be adjusted with a flat head screw driver Prevents inadvertant manual operation SMC Pneumatics, Inc.