VFR Moreover, the switch unit should be kept as close as possible to the contact protection box, with a lead wire length of no more than 1m.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
In such a case, provide an intermediate support. Provide an intermediate support with the mounting holes on the center of the path table so that the distance between supports given as L in the figure will not exceed the value shown in the graph. If the counter surface lacks precision, malfunction may result so adjust the level at the same time.
In such a case, provide an intermediate support. Provide an intermediate support with the mounting holes on the center of the path table so that the distance between supports given as L in the figure will not exceed the value shown in the graph. If the counter surface lacks precision, malfunction may result so adjust the level at the same time.
The values in these tables indicate the maximum stroke which can be used when the theoretical output is applied with an external force acting on the piston rod, or the cylinder is stopped in an intermediate position by an external stopper, etc.
These are installed with double clevis style and double knuckle joint style as standard. 2.4-17 Plate Cylinder Series MU Accessory Dimensions Single Knuckle Joint Double Knuckle Joint (mm) (mm) Applicable pin Model MUl25 MUl32 MUl40 MUl50 MUl63 Z LX RR 8.5 10 11 16 16 LD LU 11 14 15 20 20 LC 16 18 20 28 28 LB 27 31 36 46 46 Z LA 35.5 41 47 62 62 LX RR 8 10 10 16 16 LB 27 31 36 46 46 L 52.5
[Tips]
Make the distance between solenoid valve and cylinder as short as possible and especially the iock-up solenoid valve should be connected to lock port as directly as possible. eLoad fluctuation during two way skoke ol rylinder can cause piston to change its speed, which makes the stop position of cylinder fluctuate.
Make the distance between solenoid valve and cylinder as short as possible and especially the iock-up solenoid valve should be connected to lock port as directly as possible. eLoad fluctuation during two way skoke ol rylinder can cause piston to change its speed, which makes the stop position of cylinder fluctuate.
Model number: HRR012/018/24/030-AN/WN-10/20 The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRR012/018/024/030-AF/WF-10/20 The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.
[Tips]
Use care, as damage may occur if rotational force is applied to both ends of the piston rod. 5. Since CHQWB series does not have an air release plug, release air from components other than the cylinder (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use tightening torques in the table below as a guide. 2.
The counter-measure is as follows. Select control Circuit and solenoid valve that are of direct current drive and of good response time. Make the distance between solenoid valve and cylinder as short as possible and especially the lockup solenoid valve should be connected to lock port as directly as possible .
An external pilot style that can be used individually is available as a made-to-order. For details, refer to the page 4-6-46.
an additional item. *3 The USB cable (LEC-MR-J3USB) must be purchased as an additional item.
When ordering nuts as spare parts, size 4 and 5 are as shown below.
In cases of high piston speed, the use of an auto switch (G5NT) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
item. *3 The USB cable (LEC-MR-J3USB) must be purchased as an additional item.
1 AS-F !1 !2 TMH !2 !3 w ASD t y q i o e u t y q i o e u AS w AS-FE !0 KE !0 AS-FG AS-FG !9 AS-FP Meter-out type Meter-out type Meter-in type Meter-in type AS-FM Seal method: Face seal For G thread AS-D AS-T r !8 !4 !6 !7 !5 !1 ASP ASN !2 AQ w t y q i o e ASV AK !0 VCHC ASR ASQ u @0 Meter-out type Meter-in type Component Parts No.