AC Servo Motor Driver (Pulse input type/Positioning type) an additional item. *3 The USB cable (LEC-MR-J3USB) must be purchased as an additional item.
Since valves are subject to air leakage, they cannot be used for applications such as holding pressure (including vacuum) in a pressure vessel. 5. Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve.
Specify the mounting position, as well as the EXH block base or EXH block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. An EXH block base assembly is used in the blocking position when ordering an EXH spacer incorporated with a manifold no.
V (mm/s) = Auto switch operation range (mm) Load operating time (ms) x 1000 In cases of high piston speed, the use of an auto switch (D-F5NT, F7NT, G5NT and M5T) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
V(mm/s) = x 1000 In case of high pison speed, the use of an auto switch (DF7NT and G5NT) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Keep wiring as short as possible.
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
Therefore, the flow rate is calculated as the formula: Q = 0.05/1 x 20 = 1 [kg/h]. 161 VXD Series Flow Rate Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to pages 157 through to 161.
Design attachments to be as light and short as possible. Model MHZ2-10 MHZ2-16 MHZ2-20 MHZ2-25 Maximum torque Nm 0.31 0.59 1.4 2.8 Bolt M2.5 x 0.45 M3 x 0.5 M4 x 0.7 M5 x 0.8 2. Causes detection failure when using an auto switch. Ensure a stroke sufficient to allow for hysteresis, after referring to 39 Series MHZ2/MHZJ2 Air Gripper Precautions 2 Be sure to read before handling.
With Rod Boot Bore size (mm) e f h ZZ l Stroke range (mm) 40 50 63 80 100 20 to 500 43 11.2 59 1/4 stroke 154 20 to 600 52 11.2 66 1/4 stroke 167 20 to 600 52 11.2 66 1/4 stroke 178 Dimensions of the mounting brackets are the same as those of the standard double acting single rod type.
type 1.8 [1.0] 41 to 95 [5 to 35] (400 V as standard) HRSH090 Inverter type 0.18 [0.1] 41 to 104 [5 to 40] Indoor use (400 V as standard) UL Standards (To be obtained) (400 V as standard, 200 V as an option) Outdoor installation IPX4 HRSH Inverter type 0.18 [0.1] 41 to 95 [5 to 35] (200 V only as an option) 4 Thermo-chiller Standard Type Series HRS100/150 Circulating Fluid Temperature Controller
IPX4 (400 V as standard) HRS100/150 Standard type 1.0 5 to 35 V V (400 V as standard, 200 V as an option) HRSH090 Inverter type 0.1 5 to 40 V Indoor use (Only 200 V as an option) (400 V as standard, 200 V as an option) Outdoor installation IPX4 HRSH Inverter type 0.1 5 to 35 V V V V V (Only 200 V as an option) 134 Thermo-chiller Inverter Type HRSH090 Series Circulating Fluid Temperature
OFF: Position data is handled as an absolute value. ON : Position data is handled as an incremental value.
As a result, switch A turns ON.
CAT.ES20-147 A Compact Rotary Actuator Rack-and-Pinion Type/Sizes: 10, 15, 20, 30, 40 Series CRQ2 Compact Rotary Actuator Rack-and-Pinion Type/Sizes: 10, 15, 20, 30, 40 Series CRQ2 Piping can be installed from one end Body can be used as a flange Compact design saves mounting space Uses internal cushioning 10, 15 : Rubber bumper 20, 30, 40: Air cushion 10: 17mm 15: 20mm 20: 29mm 30: 33mm
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.