Integrated with a linerar guide, the MXY provides a rigid, compact and lightweight design., END CAP, ACTUATOR, MXY SLIDE TABLE, F1, 12MM MXY PART, .00000 lb
Auto switch mounting grooves have replaced the CQ2s mounting rails, preventing p, TUBE, B MOUNT, W TYPE, ACTUATOR, CQ2-Z COMPACT CYLINDER, F1, 12MM CQ2-Z PART
Auto switch mounting grooves have replaced the CQ2s mounting rails, preventing p, TUBE, A MOUNT, MAG TYPE, ACTUATOR, CQ2-Z COMPACT CYLINDER, F1, 12MM CQ2-Z PART
Auto switch mounting grooves have replaced the CQ2s mounting rails, preventing p, TUBE, B MOUNT, STD, ACTUATOR, CQ2-Z COMPACT CYLINDER, F1, 12MM CQ2-Z PART
Options include auto switch capabilities, double and single acting, mounting from 4 directions.Miniature free mount , Space saving compact cylinder , Available in 4mm to 10mm bore size, SEAL KIT, ACTUATOR, CUJ COMPACT MINI FREE-MOUNT, F1, 12MM CUJ PARTS, .10305 lb
Options include auto switch capabilities, double and single acting, mounting from 4 directions.Miniature free mount , Space saving compact cylinder , Available in 4mm to 10mm bore size, SEAL KIT, ACTUATOR, CUJ COMPACT MINI FREE-MOUNT, F1, 12MM CUJ PARTS, .10305 lb
Anti-laterial load, Bore sizes: 12, 16, 20, 25 *, Strokes: 5mm through 50mm depending upon bore size, Mounts: through hole, both ends tapped, foot, front or rear flanges, double clevis, Variety of switches and a variety of lead wire lengths, INTERMEDIATE STROKE SPACER, ACTUATOR, CQS COMPACT CYLINDER, F1, 12MM CQS PART, .00440 lb, SeriesDescriptionModelActionNoteVol. no.
PSE20xA.eng F0 Function setting F1 Function setting F99 Function setting [Initial Setting] (Function selection mode [F 0]) Set the differential pressure check mode, pressure range, and display unit of the connected sensor. M3 x 8L Panel 48 conversion adapter (Model: ZS-26-D) Default setting The default setting is as follows. If no problem is caused by this setting, keep these settings.
F0 Function setting F1 Function setting F99 Function setting Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. [Initial Setting] Set the pressure range, display unit and switch output NPN/PNP specifications.
Residual pressure error F0 Function setting F1 Function setting F99 Function setting longer in function selection mode to return to measurement mode. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
F0 function setting F1 function setting F99 function setting Do not use the product for flammable fluid. Fire or explosion can result. Only air, N2, are applicable. Flow direction Arrow Default setting Turn the power off and on again. If the failure cannot be solved, contact SMC. An internal data error has occurred.
Safety Instructions S S S Warning F0 function setting F1 function setting F99 function setting S Default setting Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result.
S S S S F0 function setting F1 function setting F99 function setting [Measurement mode] Measurement mode is the condition where the flow is detected and displayed, and the switch function is operating. This is the basic mode; other modes should be selected for set-point changes and other function settings. Do not use the product for flammable fluid. Fire or explosion can result.
F0 function setting F1 function setting F99 function setting Arrow Arrow Pressure exceeding the upper limit of the set pressure range is applied. Reset applied pressure to a level within the set pressure range. Pressure below the lower limit of the set pressure range is applied. Do not operate in an atmosphere containing flammable, explosive or corrosive gas.
F0 Function setting F99 Function setting F1 Function setting Panel : [CFM] cannot be selected if the additional range is set by the SI unit. : [w/o unit] cannot be selected if set items other than additional range are set with the units selection function. COPY receiving error Communication is not complete.
Doc.IZ*-OMU0031 / Series IZE11 2 7 8 10 10 11 14 15 18 18 F0 19 F1 OUT1 20 F2 OUT2 22 F3 22 F4 23 F5 24 F6 25 F98 26 F99 27 28 31 32 32 34 -1No.IZ*-OMU0031 1) (ISO/IEC)(JIS) 2) 1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power -General rules relating to systems IEC 60204-1: Safety of machinery -Electrical equipment
Please contact us for the latest version.sales@ocaire.com, ASSY, PISTON ROD, ACTUATOR, CQS COMPACT CYLINDER, F1, 12MM CQS PART, .31554 lb
Auto switch mounting grooves have replaced the CQ2s mounting rails, preventing p, TUBE, B MOUNT, W TYPE, ACTUATOR, CQ2-Z COMPACT CYLINDER, F1, 12MM CQ2-Z PART
Add to Cart SMC VVQ1000-16A sup block assy, VQ1000/VQ20/VQ30 VALVE*** $3.81 + Add to Quote Add To Cart Add to Cart SMC VVQ1000-1A-F1
Please contact us for the latest version.sales@ocaire.com, PISTON WASHER, VBA4100-04, AIRLINE EQUIPMENT, VBA BOOSTER REGULATOR, F1, VBA 1/2INCH PART, .01045 lb