5 Port Solenoid Valve Metal Seal/Rubber Seal Series SQ1000/2000 1 B (+) Reset 2-3-3 4 Series SQ1000/2000 Precautions 3 Be sure to read before handling.
(Tightening torque of M3 screw should be 0.5 to 0.7 Nm.) 5. Modification of the detecting position should be made in the condition of 3. CHS CH2 CHA Related Products D261
Norte Parque Industrial Valle Grande, Lampa Santiago, Chile TEL: 02-270-8600 FAX: 02-270-8601 SWEDEN SMC Pneumatics Sweden AB Ekhagsvgen 29-31, S-141 05 Huddinge, Sweden TEL: 08-603-07-00 FAX: 08-603-07-10 ARGENTINA SMC Argentina S.A.
(The tightening torque should be about 2 to 3 Nm.) 5. Modification of the detecting position should be made in the condition of 3. 329
The LVN series cannot be used as a stop valve. Be careful not to apply any excessive force to the stroke end, which fully opens and closes, to avoid accidental damage or changes in flow rate characteristics. 945
Attaching and detaching connectors If the manual override is manipulated, since any connected equipment will be activated, make sure to be done only after no danger is confirmed.
Select the cylinder with bumper (O N") it cushion valVe is to be fuH yopened. Tie rods or piston assembly may be damaged if neither air cushion nor bumper is utilized.
_c e. lf less th.n 5%, a siia er oode shou d be spec fed 2 Fof moonhng accessories sec p.ges 914 3. r8l indi.ares bdtDn mode, atsho.k rDsDlber 8L:t.rs.rnroi be added to ion butto. mo.le s of reroved 1om button node s OEr,f.1M to OEN1:10rv1 4. Lrethane sll ker caps are avalable as accessores frr rooets 0El"l1 15Mxr ro oEN,r1.25lv1r2 All diJiensions in lnches.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
No code ISC ISO 00 08 Material 2) Indication of closed status. 3) Indication of opened status.
DXT170-71-1 OFF ON VQZ It can be locked in the ON state by turning the manual override to the right, setting the E mark to 1 and pushing it. It can be unlocked by turning the manual override to the left, setting the E mark to 0 and pushing it, and the manual returns.
In the case of SRF series, when the inlet pressure is released with the condition that the pressure at outlet side is maintained, the residual pressure cannot be released. If it will be necessary to eliminate pressure from the outlet side, a circuit should be provided for residual pressure relief. 1. Open the sealed package inside a clean room.
Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
S kit can be used by connecting to gateway unit.
With 8 One-touch fittings Note) Can be changed to side ported configuration.
Because pipe fittings are press-fit, they must be replaced together with the cover assembly. r Those with a bore of 50 or more cannot be disassembled.
Actuation Warning 1 Normally closed qCannot be used for vacuum retention. wUse a release valve. (Without a release valve, the work piece may not be released.)
I nspect i on and m ai nt enance of m achi nery / equi pm ent shoul d onl y be perf orm ed once m easures t o prevent f al l i ng or runaw ay of t he dri ver obj ect s have been conf i rm ed. B. W hen equi pm ent i s t o be rem oved, conf i rm t he saf et y process as m ent i oned above.
Actuation Warning 1 Normally closed q Cannot be used for vacuum retention. w Use a release valve. (Without a release valve, the workpiece may not be released.)
P EB EA In common Type 23 Stacking type Individual wiring SY9 20 + + + + P. 43 EA P EB Manifold stations can be increased. Type 23P Stacking type Flat ribbon cable SY9 20 P. 53 Manifold stations can be increased.