Mechanically Jointed Rodless Cylinder/Basic Type Pressure Control Equipment Industrial Filters @9 !5 !6 !8 !0 @8 o @3 The numbers are the same as the "Construction" of the MY3 series catalog (CAT.ES20-165). *BLUE links will lead to purchase pages. Call or email us at sales@smcpneumatics.com for request. Replacement Parts: Seal (Order them as required with by individual part numbers.) Description Material No.
9 @0 21 @2 @3 @4 @5 Cushion seal Special resin 2 Set of left nos. !8, !9, @0, @2, @3, @4, @5 Piston seal NBR 1 21 is a non-replaceable part, so it is not included in the seal kit. Wear ring Resin 1 Piston gasket NBR Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
9 !3 The numbers are the same as the "Construction" of the Best Pneumatics No.2 Series MY1B. *BLUE links will lead to purchase pages. Call or email us at sales@smcpneumatics.com for request. Replacement Parts: Seal Kit Description Qty. Note No. MY1B10 13 Seal belt MY10-16AStroke 1 14 !6 !7 !8 !9 Dust seal band MY10-16BStroke 1 13 and 14 are not included in the seal kit.
Construction V114(A) V124(A) 2 2 Component Parts No. 1 2 3 4 5 6 Material Resin Stainless steel Resin Stainless steel, Resin FKM Stainless steel Stainless steel Description Body Cover Push rod Armature assembly Poppet Return spring Poppet spring Coil assembly Manual override 3 1 3 1 u t o e 7 8 9 Resin Replacement Parts Part no.
1A base gasket kit, NEW SY3000 MFLD*** $2.14 + Add to Quote Add To Cart Add to Cart SMC SY30M-9-2 block gasket, NEW SY3000 MFLD*** $1.28 + Add
Double acting single rod , Bore sizes *: 7/16, 9/16, 3/4, 7/8, 1 1/16,1 1/4, 1 1/2, 2 , Mounts: nose, rear, end, rod, block , Variety of switches and lead wire lengths, Optional Rod Boot, CYL, AIR 9/16 BORE, SW C *LQA, ACTUATOR, NCM ROUND BODY CYLINDER, GE, 9/16 INCH NCM DBL-ACT AUTO-SW, .00000 lb
Name Function Forward run 7 8 P-OT (/SI1) N-OT (/SI2) With overtravel prevention: Stops servomotor when movable part travels beyond the allowable range of motion. prohibited, Reverse run prohibited /DEC (/SI3) 9 Homing deceleration switch signal Connects the deceleration limit switch for homing.
Easy mode 9 4.1 Summary of Easy mode 9 4.2 Menu 12 4.3 Teaching method 13 4.3.1 Preparation 13 4.3.2 Jog teaching 13 4.3.3 Direct teaching 13 4.4 Test drive method 14 4.5 Pitch transfer method 14 4.6 Jog transfer method 15 4.7 Alarm 15 5.
Start up procedure / Connecting to a computer . 5 2. 1 Preparation . 5 (1) Confirmation of product . 5 (2) Wiring . 5 (3) Installation of the Card Motor . 6 (4) Prepared and wired by the user. . 7 (5) Software installation . 7 2. 2 Controller settings . 8 (1) Start the setup software . 8 (2) Basic Parameter Setup . 9 (3) Step data setting . 9 3Start up procedureTest operation using a computer
Then select Setting to display the System Setting window. 9. Click on the Component icon 10. Enable required Components in the Component List by ticking the radio button beside each of them. A Component that is enabled displays a green radio button.
Detection location at workpiece holding position. 9 - 3-3. Gripping force Holding conditions. To lift workpieces vertically, be sure to take into consideration the acceleration rate, air pressure, impact etc., in addition to the mass of the workpieces.
Installation 9 6. Cautions 10 7. Maintenance 11 8.
Mounting 9 4. Element Replacement 9 -1- Clean Gas Filter Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Mounting 9 4. Element Replacement 9 -1- Clean Gas Filter Clean Gas Strainer Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Helium leak volume 4.0 x 10-9 Pam3/sec or less Case/Cover Stainless steel 316 (Interior/Exterior: Electrolytic polishing) Main material Filter medium PTFE membrane Bracket Stainless steel 304 -8- 2-3 Dimensions 1) SFB300-02: Rc1/4 2) SFB302-02: TSJ1/4 (Tube Swage Joint) 3) SFB305-02, SFB315-02: URJ (Union Ring Joint) Model A SFB305-02 79 SFB315-02 84 -9- 3.
PRESS. 1. 0 M Pa O U TPU T PRESS. 0. 010. 2 M Pa M AD E I N J APAN So G No. o S o1 T P2 U Q3 V R4 W Z12 6- (1) Nm 1/4 3/8 1/2 12~14 22~24 28~30 (2) (3) (4) 7- (1) (2) (3) (4) (1) (2) (3) (1) (2) O 3 (3) 3 (4) P.5 0 (5) 0 8- (1) (2) (3) 21Nm (4) ON-OFF 5 79Nm (6) (7) (8) 0.5MPa 0.1MPa (9) AN Rc1/2 (1) (2) 9- (1) (2) 1.5~2 (1) 1 1.5 (2) (3) a b
Recommended tightening torque (Nm) Thread size 1/4 Torque 12 to 14 -9- (2) Do not apply torsion or bending moment other than the weight of the product itself.
Recommended tightening torque (Nm) Thread size 1/4 3/8 1/2 Torque 12 to 14 22 to 24 28 to 30 -9- (2) Do not apply torsion or bending moment other than the weight of the product itself.
Select an air filter with a filtration degree of 5m or finer. (9) Do not use in environments where foreign matter may stick to the product or get mixed in the product's interior. (2) Install an after cooler, air dryer or water droplet separator, etc. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment.
Mounting backward is dangerous, because the speed adjustment needle will not work and the actuator may lurch suddenly. (9)Adjust the speed by opening the needle slowly from the fully closed state. Loose needle valves may cause unexpected sudden actuator lurching. When a needle valve is turned clockwise, it is closed and cylinder speed decreases.