Series CJ5-S ø10, ø16 Stainless Steel Cylinder at stroke end) and Its Mounting Height Series CJ5-S D-H7BAL HS & $ & $ ' A B Operating Range () Minimum Stroke for Auto Switch Mounting * -!
Fig. a Fig. b CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
6 A @0 @1 !9 #2 !0 #1 A' For ball bushing #5 @5 #0 @8 !7 @6 !3 #8 !2 @1 !0 @9 For slide bearing y For long stroke For 100 @7 For 80, 100 View A-A' Parts list Parts list No. Description No.
Model Weight Weight (g) VFN2000N/Flow Characteristics Flow characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B EA/EB) VFN2120N-5D-02F 260 400 C 3.48 3.48 b 0.25 0.25 Cv 0.85 0.85 C 4.57 4.57 b 0.17 0.17 Cv 1.06 1.06 VFN2220N-5D-02F 2 position Single solenoid Double solenoid How to Order VFN2 20 1 5 D N 02 F Z Thread type Solenoid Single solenoid Double solenoid 1 2 NAMUR Interface Rc (PT) G (PF
HRR018-A (A 10) Model A B HRR012/018-A-1070 45 HRR012/018-A-2080 61 HRR012/018-A-20-U 80 50 440 (Includes protruding parts) Ventilation air outlet Ventilation air inlet 550 B 5 50 Power supply connector Operation display Circulating fluid return port Rc1/2 Serial communication connector Power supply switch Circulating fluid fill port Fluid level gauge Handle Contact input/output communication
Method 1: Calculation This formula and chart will give the Cv (Valve flow) required for operating a given air cylinder at a specific time period. Cv = Area x Stroke x A x Cf Time x 29 Area = x Radius 2 or see table B below. Stroke = Cylinder Travel (in.) A = Pressure Drop Constant (see table A) Cf = Compression Factor (see table A) Table B Cylinder Area (Sq. In.)
Method 1: Calculation This formula and chart will give the Cv (Valve flow) required for operating a given air cylinder at a specific time period. Cv = Area x Stroke x A x Cf Time x 29 Area = x Radius 2 or see table B below. Stroke = Cylinder Travel (in.) A = Pressure Drop Constant (see table A) Cf = Compression Factor (see table A) Table B Cylinder Area (Sq. In.)
Model of Switch spacer BMY3-016 33 - Auto switch operation principle Fig. (14) Auto switch operation principle In the diagram above, auto switch B is ON. When pressure is applied from A, the piston moves to B, causing the shaft to rotate clockwise. At this time, magnet B goes out of the movement range of auto switch B, causing auto switch B to turn OFF.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove.
How to replace A, B port fitting assembly By replacing manifold block fitting assemblies or the threaded port block assembly of a type 43(P) manifold, the port size of the A and B ports can be changed. To replace these parts, remove the clip with a flat head screwdriver after the valve has been removed.
B act as multipliers for the Analog Input Value x is a System Analog Input (Choose A01, A02, A03, etc.)
8 9 A B C D E F 1 4.1 + *S2 S1 DC24V MADE IN JAPAN 2 3 4 (48.5) (50) 133 10.5 10.5 5.1 4.5 5 5 Models Output unit can be used for mixed connection with PCW series.
L G ZA F H K J ZX I B C E D A ZR ZM 2 x M3 countersunk head screw mounting hole ZMA ZQ ZH ZU ZFC10, 20 ZL Applicable tubing O.D.
PF3W511/521 (Vinyl chloride piping) -38No.PF-OMN0010-J Flow characteristics of the flow rate adjustment valve PF3W504S PF3W520S PF3W540S -39No.PF-OMN0010-J Analogue output Analogue output (Flow) (PF3W504/520/540) A B C Voltage output 1 V 1.5 V 5 V Current output 4 mA 6 mA 20 mA (PF3W511) A B C Voltage output 1 V 1.4 V 5 V Current output 4 mA 5.6 mA 20 mA (PF3W521-12/14) A B C Voltage output
Note 2) When mounting a cylinder with a stroke over 100mm, use the section A mounting threads.
(When L/A IN LED is OFF.) (2)Check that the connectors of L/A IN and L/A OUT communication cables are connected and there are no broken wires. (3)Keep noise sources away from the communication cable. L/A IN and L/A OUT LEDs are OFF. LINK has not yet been established. 11 : The L/A OUT LED will be OFF if the BUS OUT connector is not used.
As a whole product, the fluid temperature range is specified as 0 to 90 oC. -69No.PF-OMN0012-H Characteristics graph Analogue output (Flow) (PF3W504/520/540) A B C Voltage output 1 V 1.5 V 5 V Current output 4 mA 6 mA 20 mA (PF3W511) A B C Voltage output 1 V 1.4 V 5 V Current output 4 mA 5.6 mA 20 mA (PF3W521) A B C Voltage output 1 V 1.5 V 5 V Current output 4 mA 5.9 mA 20 mA Rated flow
Lead wires from solenoid Lead wire at both of solenoid A and B sides in manifold is valve are connected with the terminals on upper side of connected to connector terminal as COM specification. terminal block. (On the terminal block, lead wire is connected with both A and B sides of solenoid valve in accordance with the corresponding markings A and B on the block .)
(See fig. b) -49No.EX-OMT0009 Separate power supply It is possible to provide a separate power supply to the SI unit and valves using a Y branch connector. Separate connector pin layout M12, 4 pin, plug No.
Avoid using in a place that exceeds an ambient temperature range. b. Avoid using in a place that exceeds an ambient humidity range. c. Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e.