06-rebh-e Contents Bore size (mm) REBH15-PS REBH25-PS REBH15-PS REBH25-PS 15 25 Set of left nos. @9, #0, #1, #2, #3, #4, #5 @9 #0 #1 #2 #3 #4 #5 Wear ring A Special resin Wear ring B Special resin Note) Cushion seal #5 may be difficult to be replaced. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
Contents Bore size (mm) 180 9 Resin Wear ring CQ2B180-PS A set of Nos.12, 13 and 14 from the table above 200 10 Magnet CDQ2B only CQ2B200-PS Mounting 1in = 25.4mm Mounting/Through hole type mounting bolts are available. How to order: Add "Bolt" in front of the bolts to be used.
Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 27
Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 28
MHS20-PS MHS25-PS MHS32-PS MHS40-PS MHS50-PS MHS63-PS Seal kits are sets consisting of items 10, 11, 12 and 13, which can be ordered using the kit number for each cylinder bore size. 2 Series MHS2 2 Finger Air Gripper Gripping Point The work piece gripping point distance should be within the gripping force ranges given for each pressure in the effective gripping force graphs below.
Then, the valve e is pushed down, opening the flow passage, and pressure is supplied to port 2 (A) rapidly. q r w High speed air supply PS PA Description of cylinder actuation When PS < PA after the cylinder reaches B, the main valve fully opens and PA increases rapidly as shown from C to D and becomes the same pressure as PP. t e Ps: Pressure for switching to rapid air supply Operation
a) b GR-S-010(10g )GR-S-020(20g ) P18, 4. (XC85,X446)P19 c) 4. 17 - 3-2. 3-2-1. 1 2 3 3-2-2. 1 2 3 4 5 6 7) 8 1) 2) 33. 331. 4. 20 25 32 40 CM20Z-PS CM25Z-PS CM32Z-PS CM40Z-PS 1 3-3-2. 1 2 3 4 18 - 4. (XC85,X446) 4-1. -XC85 GR-H-010(10g) <> <> 4-2. PTFE X446 GR-F-005(5g) 1) 19 - 2) () 5. 5. 20 - 6. 1.
MHW25-PS MHW32-PS MHW40-PS MHW50-PS !
L Required facility water system
MY1H40-PS MY1H25-PS Seal kit includes !
Operating time 20 s 30 s HRZ 10 s Voltage HRZD 5 s Min. 2 s HRW 1 s 0.5 s dV dt HECR = Voltage increase ratio 0.2 s 0.1 s dV HEC 0.05 s 0.02 s Time HEB 0.01 s 100 125 200 300 500 400 600 700 1000 2000 3000 4000 1500 dt HED Current (% for chiller main breaker volume) < For option B [With earth leakage breaker]> 3.
Operating time 20 s 30 s Voltage 10 s 5 s Min. 2 s dV dt 1 s = Voltage increase ratio 0.5 s dV 0.2 s 0.1 s Time 0.05 s 0.02 s dt 0.01 s 100 125 200 300 500 400 600 700 1000 2000 3000 4000 1500 < For option B [With earth leakage breaker]> 3. This product is installed with a breaker with the following operating characteristics.
Piston speed mm/s Piston speed mm/s Select the load mass from within the range of limits shown in the graphs.
Maximum piston speed: 500 mm/s It can be used at 50 to 500 mm/s provided that it is within the allowable kinetic energy range.
A set of above Nos. 46, 48, 49, 53, 54, 57 140 CS1N125A-PS 160 CS1N125A-PS Since the lock section for Series CNS is normally replaced as a unit, replacement seal kits are for the cylinder section only.
S kit can be used by connecting to gateway unit.
Contents 125 CLS125-PS A set of above Nos. 60, 62, 63, 64, 65 & 67. 140 CLS140-PS 160 CLS160-PS Since the lock section for Series CLS is normally replaced as a unit, replacement seal kits are for the cylinder section only.
Content CQ2B50-PS CQ2B50-PS CQ2B50-PS CQ2B50-PS Set of nos. above. @7, @8, @9 Set of nos. above. @8, @9, #0 Consult SMC for maintenance service. Seal kit for maintenance of the CLKQG P series with lock is not available. Consult SMC for maintenance service. Seal kit for maintenance of the CLKQG P series with lock is not available.