ZX

Because the supply valve is N.O., the pressure that is supplied to the ejector is not interrupted during a power outage; as a result, the state of suction can be maintained.

ZISE20A.eng

(When replacing the piping adapter ZS-46-N, tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. or longer simultaneously.

CA2

B A + B + 90 A 40 to 100 12 60 162 Note) This assembly drawing is provided as a reference.

SV

91.9 A A A A B A B A B A B A Dimensions are the ones for SV1300--.

Environment

As a result, it is necessary for the customer to verify conformity to the EMC directive for the machinery and equipment as a whole. w For the servo motor (24 VDC) specification, EMC compliance was tested by installing a noise filter set (LEC-NFA). Refer to page 568 for the noise filter set.

VFR

of the cylinder ports (A or B) enables use as a normally closed (N.C.) or normally open (N.O.) 3 port valve.

7ND9071en

Air connections are as follows ND9100, ND7100: G 1/4 ND9200, ND9300, ND9400, ND7200, : 1/4 NPT Liquid sealants, such as Loctite 577 are recommended for the pipe threads. NOTE: A valve controller mounted on a spring actuator must be connected only as single-acting. See Fig. 7 and 8.

MHZ

Use the table below as a guide when adjusting auto switch positions, etc.

MHZ

Use the table below as a guide when adjusting auto switch positions, etc.

NCQ8

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load which generates a surge, such as a relay or solenoid valve, use a switch with a built-in surge absorbing element. 8.

ZP

Form w 1 Material e Vacuum inlet r A Connection thread J 10 13 C B 46 29.9 21 2.5 10 8 M5 x 0.8 16 46.5 30.4 21.5 20 25 57.6 39.8 29 3.5 12 12 M8 x 1.25 32 58.1 40.3 29.5 10 13 Applicable tubing O.D.

SMC

When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Possible to transfer a workpiece at low-speed.

The maximum dimension L1 is, as a rule, twice the thread size.

3 Port Air Operated Valve Series SYJA300

4.5 41.5 [48.5] + + + + + (Station 1) (Station n) 26.1 A A 13 10 41.5 [48.5] (Pitch) P=10.5 13.5 M3 x 0.5 (A port) A A 13 10 (Pitch) P=10.5 11.5 M3 x 0.5 (A port) L plug connector (L) M plug connector (M) M8 connector (WO) Approx. 300 (Lead wire length) 41.5 [48.5] 26.1 46 28.5 52.6 [59.6] Approx. 300 (Lead wire length) 58.7 [60.9] 48.9 [51.1] 57.8 50.4 43.9 Refer to page 4-4-61 for dimensions

DOC1020530

PN01 Node address setting] or SII Configured Station Alias as necessary. You can set a node address as follows. After the node address setting is changed, cycle the power. Axis selection rotary switch (SW2/SW3) Pr.

ZISE20B-L.eng

(When replacing the piping adapter ZS-46-N, tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm.

Magnetically Coupled Rodless Cylinder

(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 7. Do not use a load that generates surge voltage. If driving a load such as a relay that generates a surge voltage, use a contact protection box.

Vacuum System Peripherals:

Must be the same voltage as that of the manifold.

Digital Flow Switches

Avoid especially the application of pressure above specifications through a water hammer. a) Use a device such as a water hammer relief valve to slow the valve's closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 8.

PF2A/PF2W

Avoid especially the application of pressure above specifications through a water hammer. a) Use a device such as a water hammer relief valve to slow the valves closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 8.