2–4 Standard Stroke (mm) Manufacturable stroke range Model Standard strokes CXSJ6 CXSJ10 CXSJ15 CXSJ20, 25, 32 60 to 100 10, 20, 30, 40, 50 80 to 150 10, 20, 30, 40, 50, 75 110 to 150 10, 20, 30, 40, 50, 75, 100 110 to 200 Strokes beyond the standard stroke range are available as a special order.
In case of high piston speed, the operating time of the load can be extended by using an auto switch (D-F7NT) with built-in OFF delay timer (approx. 200ms). 4. Keep wiring as short as possible.
The maximum number of stations is 20 in terms of manifold bases, as well as solenoids. (Please consult with SMC for more stations.)
OK OK Model determination Note 1) Stroke adjustment with either a bumper bolt or adjustment bolt is considered as an intermediate stop. Note 2) When an intermediate stop is performed with an external stopper, consider the dynamic load as shown below.
As a result, switch A turns ON.
40 HRS090 Standard type 0.5 5 to 35 Indoor use (400 V as standard) Outdoor installation IPX4 (400 V as standard) HRS100/150 Standard type 1.0 5 to 35 HRSH090 Inverter type 0.1 5 to 40 Indoor use (400 V as standard, 200 V as an option) (Only 200 V as an option) Outdoor installation IPX4 HRSH Inverter type 0.1 5 to 35 (400 V as standard, 200 V as an option) (Only 200 V as an option)
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
As a result, the inside of the bowl G, is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl G, it will not drain out.
(For details, refer to pages 20 and 21.)
Keep wiring as short as possible. Although wire length should not affect switch function, use wiring 100m or shorter. 5. Take precautions for the internal voltage drop of the switch. When designing an application, be sure to allow sufficient clearance for maintenance and inspections.
Do not use in an environment where the product is directly exposed to liquid, such as cutting oils. If cutting oil, coolant, or oil mist adheres to the product, failure or increased sliding resistance can result. 3. Install a protective cover when the product is used in an environment directly exposed to foreign matters, such as dust, cutting chips, and spatter.
11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
Remove the covers as shown in Figure (2) and make further adjustment by loosening the hexagon nut. 3. Various dimensions are indicated in Table (1). Never make an adjustment that exceeds the dimensions in the table, as it may cause an accident and/or damage.
As a result, the inside of the bowl q, is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.
Do not use in an environment where the product is directly exposed to liquid, such as cutting oils. If cutting oil, coolant, or oil mist adheres to the product, failure or increased sliding resistance can result. 3. Install a protective cover when the product is used in an environment directly exposed to foreign matters, such as dust, cutting chips, and spatter.
The position of spanner should be a root as close as possible to R thread. Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
to 500 20 to 600 20 to 600 20 to 750 20 to 750 30 to 1000 30 to 1000 30 to 1200 27 32 32 37 37 47 47 53 60 70 86 102 116 145 161 182 22 27 27 32 41 59 67 73 77 85 112.5 121 133 69 78 84 92 100 141.5 150 167 44 52 64 78 92 115 128 144 10 12 16 20 25 25 28 32 17 17 20 16 20 20 25 30 36 36 40 40 50 55 65 80 90 90 90 6.5 6.0 6.0 8.0 8.0 43 43 43 14 14 14 15 17 17 21 21 16 16 18.5 15 17 17 21