Pulse Valve -BJSXF-10B-KT JSXFA(E, F, H)-10-B-A JSXF-10B-A-KT JSXFA(E, F)-14-BJSXF-14B-KT JSXF-14B-KT2 AN30-03 (14R, 14F), AN30-N03 (14N) Disassembly/Assembly Procedure Caution Port size: 06, 10 Port size: 14 1.
(C) 55 50 60 70 80 IDU3D to 6D 45 50 55 65 75 IDU8D to 15C 45 50 55 65 70 IDU22C1, 37C1 40 45 50 55 60 IDU55C, 75C Ambient temperature (C) Outlet air pressure dew point (C) 15 10 5 15 10 5 15 10 5 15 5 10 5 15 10 1.35 1.35 0.60 1.35 1.35 0.60 1.35 1.35 0.60 1.35 0.60 1.35 0.60 1.35 1.35 25 1.35 1.05 0.50 1.35 1.05 0.50 1.35 1.10 0.50 1.35 0.60 1.20 0.55 1.35 1.25 30 1.25 0.95 0.45 1.25 0.95
50 Safety distance (mm) 40 Operational range 30 l1 20 l1 Dangerous range 10 0 5000 10 15000 20 Welding current (A) l2 50 Safety distance (mm) 40 30 l2 l2 Operational range 20 10 0 5000 10 15000 20 Welding current (A) 32 SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK EUROPE SPAIN/PORTUGAL SMC Espaa, S.A.
(Example) SS3YJ3-20-03 . 1 set (manifold base) SYJ312-5LZ-M3 . 2 sets (valve) SYJ300-10-1A . 1 set (blanking plate assembly) SS3YJ3-42R-03-C4 . 1 set (manifold base) SYJ314R-5G . 2 sets (valve) SYJ300-10-2A . 1 set (blanking plate assembly) The asterisk denotes the symbol for assembly.
10 20 A A 1 30 10 10 15 For D-F9 Rotation range m: Value of the operating range Lm of a single auto switch converted to an axial rotation range.
N L1 L2 L3 L4 L5 L6 P Q1 Q2 M KRM12-06-02-10 KRM12-06-02-6 99 10 6 6 89 47 1 4 17 19.5 33.5 23.5 33 13.5 8.5 13 19 10 125 6 108 10 55 73 106 104 KRM12-08-03-10 KRM12-08-03-6 3 8 8 19 139 11.5 22.5 37.5 26 36.5 10 15.5 20.5 14.7 86 126 119
0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x work piece weight 20 x work piece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which is at least 10 to 20 times the work piece weight.
Useable range 10 10 Load Work piece Useable range 5 5 Fn 1 0 1 2 3 4 5 6 1 0 1 2 3 4 5 6 7 8 9 10 11 7 8 9 1 01 11 21 31 41 5 Lo Distance from cylinder shaft center Lo (cm) Distance from cylinder shaft center Lo (cm) CY3B40 CY3B20 Selection example 500 200 Given a load drive resisting force of Fn = 100 (N) and a distance from the cylinder shaft center to the load application point of Lo =
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2011-2016 SMC Corporation All Rights Reserved EX-OMO0031-B
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2015-2017 SMC Corporation All Rights Reserved. EX-OMT0014-A
If the installation is using accurate control, wait until the product has warmed up (approximately 10 to 15 minutes). 1.0 to 1.2 Yellow ZS-28-C-1 Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
During the zero clear operation, pressure above 10%F.S. has been applied. After 3 s, the mode will reset to the measurement mode. The zero clear range can vary 1 digit with individual product differences. Perform zero clear operation again after restoring the applied pressure to an atmospheric pressure condition.
L/min. or CFM(ft3/min.) x 10-2 are the selectable display units. To use for flow rate indication, select the sensor and units before setting the functions [F1], [F2], [F4]. The set values for [F1], [F2] and [F4] will be reset when the flow indication setting is changed.
If the installation is using accurate control, wait until the product has warmed up (approximately 10 to 15 minutes).
Butyl acetate concentration 10% or less Nitric acid Pure water Caution Sodium hydroxide x Super pure water Strip the lead wire as shown. Do not cut the insulator. Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result.
Temperature lower limit under The fluid temperature is below -10 oC. Rise the fluid temperature. [ dtH2] Delay time setting at ON [ 0.00] 0.00 s The function number is increased and decreased by the UP and DOWN buttons.
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 04 Equivalent to M3 (L=6) 20 0.04 to 0.05 Nm 40 Equivalent to M4 (L=10) 0.09 to 0.10 Nm Element Description This unit supplies the fluid from the supply side main piping to the application.
[F20] Setting of external input Accumulated flow external reset Free range analogue output for instantaneous flow: OFF * (Analogue output for fluid temperature) Temperature lower limit exceeded The fluid temperature is below -10 oC. Rise the fluid temperature. Avoid any sealing tape getting inside the piping. Ensure there is no leakage from loose piping.
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Refer to the outline dimension drawing for mounting hole size. Refer to the product catalogue or SMC website (URL http://www.smcworld.com) for more detailed information.