Input Specification: 0 (Voltage Input), Unit Specification: M (SI Unit Only, Fixed Unit: Pa, kPa, MPa)
Series PSE digital pressure switches allow pressure to be controlled from a remote location. Series PSE510 is compact and lightweight, allowing the sensor to be mounted where needed. The use of stainless steel for all wetted parts (SUS630 for diaphragm, SUS304 for fitting) allows the PSE520 pressure sensor to be used in a wide variety of gas and fluid applications. Pressure sensor controller
Input Specification: Voltage Input, Unit Specification: P [w/Unit Selection Function, Not Allowed for Use in Japan (Initial Value psi)], Lead Wire: -
Input Specification: Current Input, Unit Specification: SI Unit Only, Fixed Unit: Pa, kPa, MPa, Lead Wire: -
Input Specification: Current Input, Unit Specification: w/Unit Selection Function, Not Allowed for Use in Japan, Lead Wire: Right Angle Lead Wire
Input Specification: Voltage Input, Unit Specification: w/Unit Selection Function, Not Allowed for Use in Japan, Lead Wire: None
Input Specification: Current Input, Unit Specification: w/Unit Selection Function, Not Allowed for Use in Japan, Lead Wire: None
Input Specification: Current Input, Unit Specification: P [w/Unit Selection Function, Not Allowed for Use in Japan (Initial Value psi)], Lead Wire: -
Input Specification: Voltage Input, Unit Specification: SI Unit Only, Fixed Unit: Pa, kPa, MPa, Lead Wire: -
Pressure Range: 0 to 1.6 MPa, Piping: NPT 1/4, Output Specification: Switch Output 1 + Switch Output 2 [NPN or PNP Switching Type], Unit Specification: -, Lead Wire: -, Bracket: -, Operation Manual/Calibration Certificate: -
PROGMBL CTRL TRNR W/AB OPTS, TRAINING EQUIPMENT SAI-, Q14, 10.88000 lb
Compact Cylinder B B Auto switch mounting surface Auto switch mounting surface Auto switch mounting surface Auto switch model Port side Port/A/B/C side A/B/C side Port/A/B/C side BQ-2 BQ2-012 Two kinds of auto switch brackets are used as a set.
10.5 [5m ] L E C P *B* (a) (b) 2 A B-1 L 1 A A-1 (b) 6 A B-1 B B-2 1 1.5m 5 A A-1 B A-2 3 3 3m B B-2 COM-A/COM B-3 4 B A-2 COM-B/A-3 5 5m (c) COM-A/COM B-3 Shield COM-B/ A-3 Vcc B-4 12 GND A-4 13 Vcc B-4 A B-5 7 GND A-4 A A-5 6 A B-5 B B-6 9 A A-5 S B A-6 8 (d) B B-6 3 B A-6 (a) + B-1 4 A-1 5 + B-3 1 2 A-3 (a) (8) (14.2) B1 A1 (b) 2 1 (17.7) (14) (18) (10.2) 6
Extension locking F Retraction locking B CLJ2 CLM2 1 CLG1 Drop prevention Emergency stop CL1 A MLGC 2 B A CNG B MNB CNA A A CNS 3 B B CLS CLQ A RLQ A 4 B MLU B MLGP ML1C Mounting Caution 1. Be sure to connect the load to the rod end with the cylinder in an unlocked condition. If this is done in the locked state, it may cause damage to the lock mechanism. 2.
5 A B CL A CL1 MLGC B Extension locking Without magnet !0o#1 @8 t CNG MNB Section A-A' Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com CNA !3 @0 CNS CLS Section B-B' (Both ends tapped) CLQ MLGP Retraction locking Section B-B' (Through-hole) !4 !7 !
AR60K-B Construction AR10-A AR20(K)-B/AR25(K)-B AC AF+AR+AL AW+AL AF+AR AF+AFM+AR AW+AFM AF Attachment AFM / AFD AR AL AW t e q IN OUT t e q r IN OUT w r w AR30(K)-B/AR40(K)-B q t AR50(K)-B/AR60(K)-B e IN OUT q t r w e IN OUT r w Component Parts No.
Refer to page 378 for minimum stroke with auto switch. 32 is for B-series rod size only. CH2 H B B 50 100 CH D2 H B B 50 100 M9BW With Auto Switch With auto switch (built-in magnet) Port and cushion valve positions Refer to page 359.
Hs A B A B 32 to 100 D-A73C D-A80C D-J79C D-A79W D-F7WV D-F7V Approx.