4 Way • 4 and 5 Port, Rubber Seal • Solenoid Pilot Valve, Series SYJ3000 How To Order: Valve Port size : Without sub-plate Body ported SYJ3 2 5 LZ 1 M3 3 Base mounted (4 Port) SYJ3 3 5 LZ 3 2 Base mounted (5 Port) (With gasket and screws) 2 SYJ3 4 LZ 3 5 M5 : With sub-plate Manual override Type of actuation : Non-locking push type 1 2 3 4 5 2 Position single solenoid 2 Position double solenoid 3 Position closed center 3 Position exhaust center 3 Position pressure
5 !4 @2 !3 w @4 @3 !6 !7 !8 !1 @1 !2 q @0 u !
(When symbol 5 is specified.) Terminal block for power supply Drain tube Terminal block for signal 127 479 Y-shaped strainer 1/2 (Accessory) 712 2 20 735 Drain tube (O.D. 10, Length approx. 2 m) (Can also be connected on the other side.) 40 752 700 1 107 Facility water inlet R1/2 64 75 Facility water inlet R1/2 (When symbol 4 is specified.)
If the product is operated 24 hours per day, the product life will be as follows: 5 min interval: life is calculated as 5 min x 1.5 million = 7.5 million min = 14.3 years 2 min interval: life is calculated as 2 min x 1.5 million = 3 million min = 5.7 years If the accumulated flow external reset is repeatedly used, the product life will be shorter than calculated life. *4 When the pressure
Description Size 090 050 Note 1 Filter Rc1 (5 F) V The value in ( ) shows the nominal filtration accuracy. Rc1/2 (5 F) V The value in ( ) shows the nominal filtration accuracy. 2 Filter Rc1/2 (5 F) V V 8 Y-strainer Rc1/2 #40 V V Install either the strainer or filter. If foreign matter with a size of 20 m or more are likely to enter, select the particle filter, and then prepare it.
1 3 4 5 0 15 10 5 0 15 10 5 20 25 30 0 15 10 5 20 Vertical L7 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 1500 1500 1500 1500 1000 1000 1000 1000 L8 [mm] L8 [mm] L8 [mm] L8 [mm] Z 500 500 500 500 Mep m 0 0 0 0 0 2 1 3 4 5 0 15 10 5 0 15 10 5 20 0 15 10 5 20 25 30 L8 Work load [kg] Work load [kg] Work load [kg] Work load [kg] Calculation of Guide Load Factor Mounting orientation
) (2 pcs.) Foot style (2) (2) Flange style (1) (2) Operating Precautions (2) (1) Trunnion style (1) Warning CJ1 One/Both side(s) Note 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fitting into the port, it is likely to damage the junction part with cover. 2. Do not operate with the cushion needle in a fully closed condition.
operated opening the valve (actuation port [2]-(7) is released).
4-3/8 4-1/2 4-3/4 4-3/4 4-7/8 5 150 5-3/8 5-3/8 5-3/8 5-1/2 5-1/2 5-1/2 5-3/4 6 CAUTION: Horizontal or angle mounted cylinders (anything other than vertical) creates a bend stress on the rod when extended, just from the weight of the rod and cylinder itself.
4-3/8 4-1/2 4-3/4 4-3/4 4-7/8 5 150 5-3/8 5-3/8 5-3/8 5-1/2 5-1/2 5-1/2 5-3/4 6 CAUTION: Horizontal or angle mounted cylinders (anything other than vertical) creates a bend stress on the rod when extended, just from the weight of the rod and cylinder itself.
5 5 5.5 5.5 Operating range Note) Operating range Note) Perpendicular electrical entry is not available for 50 and 63.
extension end KA 18.5 8.5 5 K 18.5 8.5 4.75 Vacuum suction port M5 x 0.8 5 NA-M4 x 0.7 thread depth 5 8 10 5 9.5 11 I 5.5 J 8 Maximum 11 (With stroke adjuster at retraction end) 9.5 2 Operating port 2-M5 x 0.8 4H9 depth 3.5 +0.030 0 2-M4 x 0.7 thread depth 5 HA GA 4H9 depth 3.5 +0.030 0 NN-M5 x 0.8 thread depth 10 B A 5 1 20 9 9 8.5 4.2 B A 8.5 18.5 8.5 18.5 H (NN1) x H G Section AA Section
2 !3 !4 !5 !6 No. Description Function 7 Offset function Use this function when there is a temperature offset between the discharge temperature of the thermo-chiller and users equipment.
2 6 7 Long stroke 5[-2.5] 4.5[-2] 10[-7.5] 12[-9.5] 5 5.5 9 10 5 5.5 9 10 7 6 11.5 13.5 9 9.5 13 14 11 10.5 16 18 9 9.5 13 14 12 16 20 25 11 10.5 16 18 19.5 21.5 25 27 1 0.5 6 8 17 19 22.5 24.5 7 6 11.5 13.5 Bore size (mm) Anti-lateral load 1[3.5] 0.5[3] 3.5[-1] 5.5[-3] 6 5.5 9 10 12 16 20 25 0.5 1 5 7 6 5.5 9 10 0.5 1 5 7 17 19 22.5 24.5 10 9.5 13 14 5 5.5 9.5 11.5 5 4.5 0.5 1.5 10 9.5
An example is shown below. +3 +3 +3 +3 direction + direction direction + direction 0 5 10 0 5 10 2 8 [mm] 2 8 [mm] This example shows the Target Position set at +3 mm. The table moves +3 mm from the current position.
[F30] Accumulated flow value hold setting is completed : Data memorization is performed every 5 minutes, this means that the accumulated flow value for up to 2 or 5 minutes before the power supply is turned off will not be added to the device memory.
1 Cable length [m]* *1 Mounting bracket is shipped together, (but not assembled). *2 For horizontal cantilever mounting with the rod flange, head flange and ends tapped, use the actuator within the following stroke range. Nil Without cable 2 2 5 5 A 10 !
=>Complete. 4 OUT5 [ ] After reaching of target position, INP [ ] DRIVE [ ] [ ] note.3)5) After stopping motion, BUSY [ ] SVRE [ ] 5 SVON [ ] SETON [ ] note.2) Power to the motor is cut. INP [ ] Note 1) [] means ON, [ ] means OFF. Note 2) The origin has been recognized when the operation is repeated, so it can operate without the procedure item 2.
Clean the sliding surface of the valve Oring and apply the grease. 5. A foreign object is caught in the check valve seat. (AR20K to AR60K) 5. Replace the check valve assembly. The air leaks from the exhaust port in the bonnet. 1. The diaphragm is damaged. 1. Replace the diaphragm assembly. 2. The piston seal is damaged. 2. Replace the piston assembly or clean it.
Clean the sliding surface of the valve Oring and apply the grease. 5. A foreign object is caught in the check valve seat. (AR20K to AR60K) 5. Replace the check valve assembly. The air leaks from the exhaust port in the bonnet. 1. The diaphragm is damaged. 1. Replace the diaphragm assembly. 2. The piston seal is damaged. 2. Replace the piston assembly or clean it.