Refrigerated Air Dryer For Use in North, Central and South America If it is unavoidable that the tube goes upward, make sure it only goes as far as the position of the auto drain outlet. The drain tube to be prepared should have an O.D. of 0.47 in (12 mm), an I.D. of 0.31 in (8 mm) or more, and be 16.4 ft (5 m) or less in length.
Accessory None (Standard) With bracket (Except IDG1) Nil B Note) When symbol B is indicated, a bracket assembly with a part number shown in the table below is included as an accessory.
which is provided as an accessory part, through the rubber cap (it is not necessary to remove the rubber cap).
An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. 8 Direct Operated 2 Port for Oil Series VCL 2 Port Solenoid Valve for Fluid Control/Precautions 1 Be sure to read before handling Precautions on Design Selection Warning Warning 1. Cannot be used as an emergency shutoff valve, etc.
When cylinders are used in close proximity to one another as in mounting patterns (1) through (4), the magnetic force of the auto switch magnets in cylinder B may have an effect on the operation of the auto switches on cylinder A.
For an environment that needs the water resistant auto switch, select the D-M9mA(V) type.
optional manifotd mounted deslgn is available tor the NVS 3115 valves, The block 13 aluminum bar Etock with common supply and exhaust as wellaa an individual outlet port on the side.
The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Set the operating pressure using the graphs shown on the right as a guide.
Manual release bolt Design minimizes influences of unlocking air quality A design largely unaffected by factors such as moisture and condensate in compressed air has been realized by separating the lock mechanism and the brake cylinder. Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder.
When used for a gas, the product is handled as a class 2 pressure vessel compliant special order product. (Except for products with an internal capacity of less than 40 L) Note 7) Confirm the lead time with each order.
Pressure Since valves are subject to air leakage, they cannot be used for applications such as holding pressure in a pressure vessel. Moreover, when used for vacuum, use type m. 4. Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Limited warranty and Disclaimer 1.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Mixed single and double wiring is available as an option.
an auto switch when mounting a housing of 10.
(Mainly when using an external guide) When using it as a load balancer, please contact SMC sales representatives. Load mass (kg) m1 MY1B MY1B MY1H 3. Consider uncalculated loads such as piping, cableveyor, etc., when selecting a load moment Calculation does not include the external acting force of piping, cableveyor, etc.
Front matter 7 16 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.