5 Clevis Pin x Material: Cast iron 80, 100 L2 Material: Carbon steel (mm) Part no.
CUJ Allowable Kinetic Energy Allowable Lateral Load at Rod End Without Auto Switch CU Table (1) Load Weight and Piston Speed .
Applicable solenoid valves: Series SYJ314, SYJ314M, SYJ324, SYJ324M (SYJ300 3 port valve) (SYJ300 3 port valve) Plug (VJ3000-33-1) Plug (VJ3000-33-1) Seal the unused R port at the end the manifold. Seal the unused R port at the end the manifold.
Applicable solenoid valves: Series SYJ314, SYJ314M, SYJ324, SYJ324M (SYJ300 3 port valve) (SYJ300 3 port valve) Plug (VJ3000-33-1) Plug (VJ3000-33-1) Seal the unused R port at the end the manifold. Seal the unused R port at the end the manifold.
10mA load current) 0.8V or less 4V or less Internal voltage drop 100A or less at 24VDC 0.8mA or less at 24VDC Leakage current Internal circuits Actuated position .
10mA load current) 0.8V or less 4V or less Internal voltage drop 100A or less at 24VDC 0.8mA or less at 24VDC Leakage current Internal circuits Actuated position .
Table displacement due to yaw moment load Displacement at A when load is applied at F . Table displacement due to roll moment load Displacement at A when load is applied at F .
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
L2 L2-10.5 L1=(28 x n)+56 18 20 28 28 5.3 28 5.5 84 SMC SMC SMC SMC 8 52.5 39 3 5 11.5 6 L2 dimension DIN rail part no.
Dynamic moment RB Me3 Guide central axis J L2 We W Examine Me3.
Dynamic moment RB Me3 Guide central axis J L2 We W Examine Me3.
In cases where an auto switch magnet is attached, please add -M9// at the end of the part number. (Not available for high temperature models) Note 3) Auto switch and solenoid valve are not attached. When a set including auto switch and solenoid valve is required, please add the symbols after the auto switch in How to Order at the end of the part number.
} L3=50 {mm} L2=50 {mm} L2 {B L3 Item Load factors n Note (1) Max. movable load W B L2 Examine W.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
tighten the threaded portion by hand, then use a proper wrench, which could be Rz 12.5 suitable for the width across flats of the hexagon body, to tighten it further at a wrench For Uni thread, Rz 12.5 is necessary for sealing at the chamfered part. 45 tightening angle shown in the table below.
tighten the threaded portion by hand, then use a proper wrench, which could be Rz 12.5 suitable for the width across flats of the hexagon body, to tighten it further at a wrench For Uni thread, Rz 12.5 is necessary for sealing at the chamfered part. 45 tightening angle shown in the table below.
L2 [mm] L2 [mm] L2 [mm] L2 [mm] 120 120 120 120 Me m Y 80 80 80 80 40 40 40 40 0 0 0.2 0.4 0.6 0.8 1 0 0.0 0.4 0.8 1.2 1.6 2.0 0 0.0 0.4 0.8 1.2 1.6 2.0 0 0 0.2 0.4 0.6 0.8 1 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 300 300 200 200 250 250 160 160 Me 200 200 L3 [mm] L3 [mm] L3 [mm] L3 [mm] 120 120 m L3 150 150 Z 80 80 100 100 40 40 50 50 0 0 0.2 0.4 0.6 0.8 1 0 0.0 0.4
Burst pressure Note) Min. bending radius (mm) 24 Burst pressure (MPa) Operating temperature Material 20C to 60C Nylon 12 Note) The value at temp. of 20C and with O.D. variable rate 10% max.
There are 2 green indicator needles, to be set at the upper and lower limits of the pressure range.