Magnetic Separator FHM Series Insulation resistance 30 m or less Contact resistance Between terminals with the same pole. 1,000 VAC 50/60 Hz 1 min FH FH Between charged metal Withstand 1,500 VAC 50/60 Hz 1 min part and ground voltage HOW Between each terminal and 1,500 VAC 50/60 Hz 1 min non-charged metal part 529 Hydraulic Filters/Precautions 1 Be sure to read this before handling products.
temperature (Humidity) oC 2 to 40 (Relative humidity 85% or less) Note 3) Power supply Note 5) 3-Phase 200 VAC (50Hz), 200/ 220 VAC (60Hz) Electrical specifications 17.3 26.1 Operation current Note 6) 50/60Hz 3-phase 200V A 17.9 26.4 4.6 6.0 Power consumption 50/ 60Hz, 3 phase 200V kW 5.6 7.3 Earth leakage breaker capacity Note 7) (Sensitivity current 30mA) A 50 Cooling method of the condenser
General specifications Item Specification Enclosure IP20 Ambient operating temperature -10 to +50oC Ambient storage temperature -20 to +60oC Ambient humidity 35 to 85% RH (no condensation) Withstand voltage 500 VAC 1.0 min.
Switch Internal Circuit D-Y7GL Motor model Compatible driver model Power supply voltage (VAC) Motor output (W) + Brown lead wire MSD5A1P1E 100/115 Main circuit of switch Matsushita Electric Industrial Co., Ltd.
Comparison of potential amplitude between AC type and dual AC type (Installation height of sensor: 300 mm) 40 AC type Surface potential of workpiece (V) 20 25 V or less Dual AC type IZS42 0 20 40 Time Independent Dual AC type is implemented.
How to Order VFN212 02 N 5 F D Z CE marking NAMUR Interface Nil Q CE marked product Voltage Thread type 1 100 VAC, 50/60 Hz 2 200 VAC, 50/60 Hz 3 110 to 120 VAC, 50/60 Hz 4 220 VAC, 50/60 Hz 5 24 VDC 6 12 VDC 7 240 VAC, 50/60 Hz Nil Rc (PT) F G (PF) N NPT Electrical entry Solenoid G Grommet E Grommet terminal T Conduit terminal D DIN terminal Nil Single solenoid D Double solenoid Manual
70 78 8/Rc 10/Rc 5 8 13 12 20 23 24 34 46 40 70 78 55 75 95 65 110 150 85 135 185 SUP VAC EXH 28 28 33 66 11 12 16 27 43 55 95 ZH ZH07B ZH10B ZH13B ZH05D ZH07D ZH10D ZH13D ZH15D ZH18D ZH20D 1 8 1 8 Box type (Built-in silencer) 0.7 1.0 1.3 0.5 0.7 88 48 1 4 1 8 ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local
Note) Flow rate corresponds to VAC pressure of 101kPa, SET pressure of 80kPa, and initial flow rate setting of 0l/min(ANR).
Contact capacity 50 VA AC, 50 W DC 1 2 5 100 VAC (50/60 Hz) 200 VAC (50/60 Hz) 24 VDC Pressure gauge for supply pressure Pressure gauge for tank pressure Pilot valve Recommended Equipment AIR BLOW Supply pressure AIR It is recommended to use each mist spray unit type with the mixing valves, magnet holders, branch pipes and nylon tubes listed in the table below.
, 110 VAC, 200 VAC, 220 VAC, 24 VDC Allowable voltage range (%) 15 to +10% of rated voltage Coil insulation Class B or equivalent 50 Hz 5.6 Apparent Inrush 60 Hz 5.0 power 50 Hz 3.4 (VA) Holding 60 Hz 2.3 Power consumption (W) 1.8 Surge voltage suppressor and indicator light Available as option Note 1) Pilot pressure range should be 0.1 to 1 MPa (14.5 to 145 psi).
Copper, fluorine and silicone-free + Low particle generation 22 Vacuum suction type Reed switch Auto switch A90 Solid state M9B, M9N A With adjustment bolt R With internal shock absorber Auto Switch Specifications Load voltage Load current range Indicator light Applicable load Type Auto switch model 24 VAC or less, 48 VAC or less, 100 VAC or less 24 VDC or less, 48 VDC or less, 100 VDC or
Operating humidity range [%RH] 90 or less (No condensation) Regeneration option May be required depending on speed and work load Motor output/Size 100W/40 200W/60 Electric specifications Motor type AC servo motor (100/200 VAC) Encoder Incremental 17-bit encoder (Resolution: 131072 p/rev) Horizontal 45 65 Power consumption [W] *5 Vertical 145 175 Horizontal 2 Standby power consumption when
Red (DC) Blue 100 VAC 110 VAC 200 VAC 220 VAC Red Blue 100 VAC 110 VAC Red 200 VAC 220 VAC Push type (Tool required) Push down on the manual override button with a small screwdriver until it stops. Release the screwdriver and the manual override will return.
50/60 Hz 200 VAC 50/60 Hz 110 to 120 VAC 50/60 Hz 220 VAC 50/60 Hz 24 VDC 12 VDC 240 VAC 50/60 Hz Nil F N Rc (PT) G (PF) NPT Manual override Non-locking push type (Flush) Non-locking push type (Extended) Locking type (Tool required) Nil A B Other Electrical entry Light/Surge voltage suppressor G E T D DO Grommet Grommet terminal Conduit terminal DIN terminal DIN terminal (Without connector
Check that the main circuit power supply (200 VAC) and controller circuit power supply (200 VAC) are wired correctly. When using the emergency stop SW etc. provided by customer, wire it to the EMG (Forced stop) of the input/output signal(CN6-1). When wiring, I/O connector(LE-CSNA) or I/O cable(LEC-CSNA-1) is required. (EMG (Forced stop) cannot be controlled with CC-Link.)
(50/60 Hz) 200 VAC (50/60 Hz) 110 VAC (50/60 Hz) 220 VAC (50/60 Hz) 24 VDC 12 VDC Other 1 2 3 4 5 6 9 Note) Option Note) Except large flow type.
Indicator light LED Can be used for 110 V and 115 VAC, 220 V and 230 VAC in common.
d1 = d3 for sizes 20 to 40. A parallel keyway is used on the long shaft for size 40. Minimum machining diameter for d1 is 0.1 mm.
d1 = d3 for sizes 20 to 40. A parallel keyway is used on the long shaft for size 40. Minimum machining diameter for d1 is 0.1 mm.