Toggle Type Air Gripper

Applicable bore size D-A72 D-A73 Grommet (Perpendicular) Without indicator light D-A80 D-A79W Diagnosis (2-color indicator) Reed switch D-A73C Connector (Perpendicular) D-A80C Without indicator light D-A72H Grommet (In-line) D-A73H, A76H D-A80H Without indicator light BQ5-032 32 to 63 D-F7NV, F7PV, F7BV D-F7NWV, F7BWV Diagnosis (2-color indicator) Grommet (Perpendicular) D-F7BAVL Water

Clamp Cylinder Series CK1

D-P4DWSC D-P4DWSE D-P4DWL D-P4DWZ BA8-032 Dimensions 25 28 5 6 12 3 x Rc 1/8 3 x Rc 1/8 9.5 20 4 Speed controller valve Cushion valve 4 32 12 4 45 45 M10 x 1.25 Max. 26.5 12 40 26 41.5 Width across flats 36 12 R12 12 +0.5 +0.2 Shaft: 10 0.040 d90.076 28 26 Hole: 10 +0.022 H8 0 41.2 38 5 20 34 + Stroke 70 + Stroke 55 137 + Stroke Double knuckle joint Single knuckle joint 10 +0.022 H8 0 3

Title not found

When sp4l4ng two or more oplons, 6l symbols r alphabelicalorder Exampl:.BRS Nole 1) When using lhe back pressure check valve lirr lhe necessarystalions on y enterlhe back pressure clrekEl@ part no and indcale the nlmber of hanilold strlons n the spfcaton sheet Nole2) ForspecralDlN ra lenglh. ndicate DlE.terthe numberol slalons Insde ll) 1 to 10 (20) Top ported elbow Wilh 032 Onelouch lilting

Fine Lock Cylinder with Guide Series MLGC ø20, ø25, ø32, ø40 2

BMA2 -025 BMA2 -032 BMA2 -040 OUT IN (N) Theoretical Output Piston area (mm2) Operating pressure (MPa) Bore size (mm) Rod size (mm) Operating direction 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 The following set of mounting screws made of stainless steel is also available. Use it in accordance with the operating environment.

MB1

BMP1-032 70C J Nylon tarpaulin 110C K Heat resistant tarpaulin Maximum ambient temperature for the rod boot itself. 6-7-5

Hygienic Design Cylinder Series HY

Auto switch model Bore size (mm) 20 25 32 40 50 63 80 100 D-H7BA D-G5BA BMA2-020 BMA2-025 BMA2-032 BMA2-040 BMA2-050 BMA2-063 BA-08 BA-10 When the auto switch bracket above is ordered as a single unit, steel screws are included. When assembling, use the stainless steel screws attached to the auto switches shown below.

Mechanically Jointed Rodless Cylinder Series MY1

Separate switch spacers (BMP1-032) are required for retrofitting of auto switches. There are other applicable auto switches than listed above. For details, refer to page 1053. For details about auto switches with pre-wired connector, refer to pages 1328 and 1329.

17

When installing the D-P4DW, use the BMG7-032 auto switch mounting bracket. 22 Series MGP Auto Switch Mounting 2 Auto Switch Mounting Brackets/Part No. Applicable Cylinder Series: MGPM, MGPL, MGPA D-M9/M9V D-M9W/M9WV D-M9A/M9AV D-A9/A9V D-P3DW Applicable auto switches Bore size (mm) 12 to 100 25 to 100 Auto switch mounting bracket part no.

Model: 20 to 50mm Bore, Applicable Bore Size: 032 (32 & 40mm Bore)

Model: 20 to 50mm Bore, Applicable Bore Size: 032 (32 & 40mm Bore), Type: Z

Mounting: F (Flange), Applicable Bore: 032 (25mm, 32mm)

Mounting: L (Foot, Requires 2 Per Cylinder), Applicable Bore: 032 (25mm, 32mm)

Mounting: D (Double Clevis w/Pin), Applicable Bore: 032 (25mm, 32mm)

Mounting: T (Trunnion w/Nut), Applicable Bore: 032 (25mm, 32mm)

Mounting: C (Single Clevis), Applicable Bore: 032 (25mm, 32mm)

Size: 032 (For NCG 32)

Size: 032 (For NCG 32)

Prefix: CG (Selection for "T" Mount 25 & 32mm Bore), Mounting: T (Trunnion), Applicable Bore: 032 (1 1/4")

Prefix: NCG, Mounting: D (Double Clevis), Applicable Bore: 032 (1 1/4")

Prefix: CG (Selection for "T" Mount 25 & 32mm Bore), Mounting: L (Foot, Requires 2 Per Cylinder), Applicable Bore: 032 (1 1/4")