KG Seal Tube Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0 MPa The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Body (White) O-ring Stud Effective when piping in a confined space. The body and the threaded portion can rotate. PAT.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Bulkhead union P. 60 KCE Use to connect tubes through a panel. One of two ports has a self-seal function. Bulkhead connector P. 60 KCE Use to connect male thead and tube through a panel. 15-2-67 Series KC Precautions Be sure to read before handling.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
Setting Position (mm) D-C7 D-C8 D-C73C D-C80C D-G39 D-K39 D-A33, A34 D-A44 D-B5 D-B6 D-H7l D-H7C D-G5NTL D-H7lW D-H7lF D-H7BAL D-B59W Bore size (mm) A B A B A B A B A B A B A B 20 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.5 29.0 53.0 28.5 49.5 25.0 25 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.5 29.0 53.0 28.5 49.5 25.0 32 59.5 36.5 53.5 30.5 58.0 35.5 55.0 32.5 57.0 34.0 56.5 33.5 53.0
2 w i A CJ1 CJP CJ2 A Cylinder tube sectional view A-A !0 o CM2 CG1 Component Parts MB No. q w e r t y u i o !0 !1 No.
Cracking pressure is a pressure at which the valve starts opening and not a pressure at which the valve is fully open. 15-8-7
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
When replacing mounting bracket, use a hexagon wrench. MB Mounting/Piping Caution MB1 1. Mounting a workpiece on rod end To screw a bracket or a nut onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes.
pin should be used together with a plain washer.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
A flexible polyurethane tube is recommended when the lateral load is applied. 15-2-39
Series KS/KX Male connector: KSH (Standard) H (width across flats) Applicable Connection thread R Min. port size Effective area (mm2) Nylon Urethane
In order to prevent a malfunction or diaphragm damage caused by debris or cutting chips in the fluid, install a filter with approximately 100 mesh on the inlet side of a flow switch. C (COM) A (N.O.) Color of lead wire Black Symbol Contact C Z I SE3 Common A White Normally Open B (N.C.)
+0.4 +0.2 CW CX CZ L RR CT CZ -0.1 -0.3 CW B + Stroke L 10 15 6.5 12 8 6 RR CL + Stroke 16 18 8 16 10 9 A + Stroke 20 20 10 20 10 10 25 20 18 36 12 10 30 22 18 36 12 10 40 28 22 44 12 14 8 Series MQQ Accessory Dimensions Female-male thread conversion joint Rod end nut d NN Rod MM D C C B H E F A B H Applicable bore size (mm) Applicable bore size (mm) Part no.
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
D-Y7WV D-Y7BAL D-A3 D-A44 D-G39 D-K39 D-A5 D-A6 D-A59W D-F5NTL D-F5LF D-P5DWL Bore size (mm) A A A A B A A A A B B B B B B B 32 12 11 7 4.5 0 0.5 3.5 4 0.5 9.5 8.5 4.5 2 1 1.5 0 40 12 11 7 4.5 0 0.5 3.5 4 0.5 9.5 8.5 4.5 2 1 1.5 0 50 12.5 11.5 7.5 5 0 1 4 4.5 1 10 9 5 2.5 1.5 2 0 63 12.5 11.5 7.5 5 0 1 4 4.5 1 10 9 5 2.5 1.5 2 0 80 15.5 14.5 10.5 8 2.5 4 7 7.5 4 14 13 9 6.5 5.5 6 2.5 100
Contact SMC if a stopper cylinder is to be used for stopping a load that is connected directly to a cylinder, as this will cause the cylinder's thrust to act as a horizontal load.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
A unique positioning mechanism allows accurate installation and removal of tubing with ease even in a hardto-see locations, while preventing piping errors when reconnecting. Plug Holder Socket Plug case Irregular shape permits engagement in a proper position.
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.