There is a maximum 46% reduction in size, reducing required maintenance space.? The AF bowl (size 30 and 40) is covered with a transparent bowl guard, allowing 360 monitoring.??The modular design of the AF allows connection with other SMC air preparation equipment.
V www.stevenengineering.com I 6.11 VACUUM VACUUM PADS SERIES ZP H O W T O O R D E R ZPT P A D V E R T I C A L T Y P E W I T H O U T B U F F E R ZPT V A C U U M E N T R Y ( A L S O M O U N T I N G T H R E A D D I A) P A D D I A M E T E R S Y M B O L T H R E A D D I A M E T E R 2~ 8 10~ 16 20~ 32 40 50 02 2 04 4 06 6 08 8 10 10 13 13 16 16 20 20 25 25 32 32 40 40 50 50 P A D M AT E R I A L Male
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
M a n i f o l d m o u n t e d v e r s i o n s o f t h e V YH y r e g a r e a v a i l a b l e .
i s p e r u s s e r p g n i t a r e p o . x a M ) 7 . 0 ( 0 0 1 g i s p * e g n a r g n i t a r e p o l a i t n e r e f f i d e r u s s e r P ) a P M ( ) 6 . 0 ~ 1 . 0 ( 0 9 ~ 5 1 e g n a r . p m e t g n i t a r e p O F 0 4 1 ~ 0 4 t n a c i r b u l d e d n e m m o c e R ) 2 3 G V O S I ( 1 # l i O e n i b r u T l w o B e t a n o b r a c y l o P T L A N k n a T d e e F o t u A 5 T L A
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
No cracks, breaks or other damage occurred in a drop test from a 2-meter height or in a human stomp test.
Then, a correct operation works until a vacuum pressure proportional to the input signal is reached, and a vacuum pressure is obtained which is always proportional to the input signal.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. outdoors or in a place exposed to direct sunlight. 2.
None K Lock Nut Hexagonal Width across Flat (Special Order) N Nickel Plating A R E A C O D E Ambient and Fluid Temp 0 ~ 60OC / 32 ~ 140F ...
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
Warning: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.
Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.
If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side.