SMC Corporation of America
Elite Part Number Search
Search Results "E600-06-A"

D-Y7BAL D-A3 D-A44 D-G39 D-K39 D-A5 D-A6 D-A59W D-F5NTL D-P5DWL Bore size (mm) A B A B A B A B A B A B A B 32 1 3.5 1.5 4 0 0.5 9.5 12 4.5 7 2 4.5 0 0.5 CL 40 1 3.5 1.5 4 0 0.5 9.5 12 4.5 7 2 4.5 0 0.5 50 1.5 4 2 4.5 0 1 10 12.5 5 7.5 2.5 5 0 1 CL1 63 1.5 4 2 4.5 0 1 10 12.5 5 7.5 2.5 5 0 1 80 5.5 7 6 7.5 2.5 4 14 15.5 9 10.5 6.5 8 2.5 4 MLGC 100 5.5 7 6 7.5 2.5 4 14 15.5 9 10.5 6.5 8 2.5

Diaphragm Assembled in a clean room.

Also, take measures to prevent ingress of water and foreign matter from the breathing port of the diaphragm. 5-5-10 1 3 Port Air Operated Valve Series VGA342 How to Order SA 04 VGA342 A VA Port size Passage A Normally closed (N.C.) B Normally open (N.O.) Thread type Nil Rc F G N NPT T NPTF 04 1/2 06 3/4 10 1 SA VA JIS Symbol VM N.C. N.O.

[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.

Although the circuit at the output side of the switch is surgeprotected, damage may still occur if a voltage surge is applied repeatedly. When a load which generates a surge, such as from a relay or solenoid valve, is directly driven, use a switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications.

-DN Manifold A B A B VVQ1000FPG 06 Cautions PSince air leakage from the pipe between the valve and cylinder or the fittings will prevent the cylinder from stopping for a long time. Check for air leakage using neutral household detergent, such as dish washing soap. Also check the cylinders tube gasket, piston seal and rod seal for leakage.

When ordering only a vessel, it is not necessary to enter the symbol for built-in elements. The membrane element cannot be selected for FGH100. Port size 03 04 06 10 Rc3/8 Rc1/2 Rc3/4 Rc1 Since this product uses PTFE for gasket material, a large torque is required to tighten a clamp ring. The FKM specification with the clamp ring tightening torque reduced is also available.

When ordering only a vessel, it is not necessary to enter the symbol for built-in elements. The membrane element cannot be selected for FGH100. Port size 03 04 06 10 Rc3/8 Rc1/2 Rc3/4 Rc1 Since this product uses PTFE for gasket material, a large torque is required to tighten a clamp ring. The FKM specification with the clamp ring tightening torque reduced is also available.

P = 43 PA 23 A A B B 14 12 A PA PA L1 L2 L2 L1 B B B 14 12 A A A A B 14 A A PA B B (2n 1/8) 4n-1/4, 3/8 2, 4 port PA L-side R-side L-side R-side D-side D-side 89 3 89 16 141 (Single) 141 (Single) 55 44 186 (Double) 186 (Double) 196 (3 position) 196 (3 position) 77.5 Bottom ported M12 connector L: Dimensions n: Stations 141.5 L n 1 Formula 2 3 4 5 6 7 8 9 10 121 5 1 12 14 PA PB 107 L1 = 43n

Model A side B side JIS Symbol A relay output module of devices up to 110 A B is available for control VAC, 3 A. 4(A) 2(B) A B N.C. valve N.C. valve 3(EB) SOL.b SOL.a 1 2 SV A00 5(EA) B side passage symbol: Green B side manual override: Green Tie-rod base manifold (For SV1000/2000/3000/4000) 1(P) 4(A) 2(B) A side coil A side spool valve B side spool valve N.O. valve N.O. valve 1 2 SV B00

A side manual override: Orange A side passage symbol: Orange A B A B B side passage symbol: Green B side manual override: Green Pull the lever forward with a screw driver, etc.

A spring washer will be required separately for VP470.

It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.

It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.

Spare parts Short, medium, and long paddles are provided as a 3 piece set with each model, so arrange them as indicated below. There is no compatibility between the paddle for a 3/4B connecting bore and for a 1B because their installation pitches differ. Arrangement example: Paddle set for IF300-06-00 (Part number are not existed.)

Cooling water (l/min) 180C Inlet air temperature Correction factor Air flow (l/min (ANR)) Model 50C 70C 100C 41.5 43 45.5 37 43 49.5 37 43 45.5 37 42 43.5 40 44 46 39.5 43 44.5 41 43 45.5 A B C A B C A B C A B C A B C A B C A B C 35.5 36 36.5 33.5 36 38 33.5 36 36.5 33.5 35 36 34.5 36 37 34.5 35.5 36 34.5 35.5 36 38.5 40 42 36 40 45.5 36 40 42.5 36 40 41 38 40 42.5 38

(mm) H2 Q P L W H1 Model TMA-06 TMA-08 TMA-10 TMA-12 28 21.7 172.5 31.8 25.4 151.2 35 28.1 167.3 37 19 151 17.9 20.3 24.3 26.7 18.6 18.6 22 22 11.4 12.6 15 16.2 6 12 10 8 15-6-32 1 Related Products: Tube Cutter Series TK Tube Cutter: TK-2 Possible to cut a tube up to 18 mm.