SMC Corporation of America
Elite Part Number Search
Search Results "HRS100-AN-46-A"

BQ2-012 is a set of d and e shown above. 32 to 100 When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.

Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.

Note 1) When using a D-F8 switch, mount it at a distance of 10 mm or more from magnetic substances such as iron, etc. Note 2) Add -61 at the end of the part number for the flexible lead wire. MHY MHW (Example) When ordering with an air gripper When ordering auto switches only. MRHQ 61 D-F8PL61 MHZ 2-16D-F8NSMisc.

Note 1) When using a D-F8 switch, mount it at a distance of 10 mm or more from magnetic substances such as iron, etc. Note 2) Add -61 at the end of the part number for the flexible lead wire. MHY MHW (Example) When ordering with an air gripper When ordering auto switches only. MRHQ 61 D-F8PL61 MHZ 2-16D-F8NSMisc.

For DC, W=V/A (Note) cos (Note) cos shows power factor. w Surge voltage The surge voltage is a high voltage generated momentarily when cutting the power supply. e Hum sound The hum sound is a noise generated through repeated adsorption and releasing on an armature adsorption surface.

Troubleshooting If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident. Error indication function This function is to display error location and content when a problem or error has occurred.

Troubleshooting If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident. Error indication function This function is to display error location and content when a problem or error has occurred.

If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.

Through the concurrent use of a CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. A cushion mechanism is provided on the cover at both ends to absorb the impact that is created during high speed operations.

When combining a double check valve and an interface regulator, use a manifold or subplate as a basis, and stack them in the following order; the perfect spacer the interface regulator the valve.

PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn for a port size of M3 x 0.5 or 1/6 turn for a port size of M5 x 0.8. For elbow type fittings, tighten an additional 1/2 turn for a port size of M3 x 0.5 or 1/3 turn for a port size of M5 x 0.8 if gaskets are mounted in two places.

Blinks when an overcurrent error occurs on OUT1. DOWN Button ( Button) Use this button to decrease a set value. UP Button ( Button) MODE Button ( Button) Use this button to increase a set value. Use this button to change a function. SET Button ( Button) Connectors Use this button to select a function. Connectors shown below are applicable (female contact).

MXW MXP Air-hydro Copper Free MG Low hydraulic pressure cylinder under 1.0MPa Through the concurrent use of a CC Series air-hydro unit, it becomes possible to operate at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.

rimes UV rne etea of lever. works on the brake shoe. then turns into a large gripping force which tightens on the piston rod to lock il. To release lock up, apply air pressure Io reteasjng port to eljmiDale lhe sprjng torce. Air pressure lock-up Spring with air pressure lock-up An pressure Air pressure s'-pp,y exhausl I t Afpressure An p@ssure supPry 4rEst !

rimes UV rne etea of lever. works on the brake shoe. then turns into a large gripping force which tightens on the piston rod to lock il. To release lock up, apply air pressure Io reteasjng port to eljmiDale lhe sprjng torce. Air pressure lock-up Spring with air pressure lock-up An pressure Air pressure s'-pp,y exhausl I t Afpressure An p@ssure supPry 4rEst !

An ideal air cylinder for lifting and pressing operations. Air pressure supplied from A operates on surfaces 1 and 2. (extension) A B Air pressure supplied from B operates on surface 3. (retraction) A B Mounting accuracy improved Positioning holes are provided on the work piece mounting surface for easy alignment.

For connection with a load having an external support/guide mechanism, select an appropriate connection method and perform careful alignment. Use caution, as scratches or nicks, etc. on the sliding parts of the piston rod can cause malfunction and air leakage.

For connection with a load having an external support/guide mechanism, select an appropriate connection method and perform careful alignment. Use caution, as scratches or nicks, etc. on the sliding parts of the piston rod can cause malfunction and air leakage.