Fieldbus system EtherNet/IP TM compatible SI Unit IO-Link Master Unit A unit connected to a PLC to communicate input and output data. U U Side The side connected to the solenoid valve when the product is connected to a manifold. -10No.EX-OMX1011 Assembly Composing the unit as a manifold : If the unit was purchased as a manifold, the work described in this section is not necessary. (1) Connect the unit to the end plate.
If the chewed portion of the tubing is used as is, this can cause trouble such as air leakage or difficulty in removing the tubing. 2. When mounting a One-touch fitting, use a suitable wrench to tighten the hexagonal flats of the fitting. Moreover, position the wrench at the lower part of the hexagonal flats as close to the threads as possible.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
The U-shaped groove is machined into the cushion ring in such a way that this acceleration process can proceed smoothly (as a sine function).
To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve, and place the solenoid valve as close as possible to the cylinder. 4. Note that the stopping accuracy will be influenced by changes in piston speed.
The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 mm Applicable shaft types: X, Z The maximum dimension L2 is, as a rule, twice the thread size.
Dual 2-port valve (Supply valve/Release valve) MSupply valve: Self-holding1 Even if there is a power cut, the vacuum is maintained as long as there is supply air. q The vacuum is maintained during power failure as long as air is supplied. This can prevent the workpiece from being dropped. w The unit turns on by instantaneous energizing (minimum 20 ms.).
The maximum dimension L1 is, as a rule, twice the thread size.
MQ D-G5, K5, G5lW D-K59W, D-G59F, D-G5NT 20 to 100 D-C7, C8 20 to 63 RHC 8.5 Auto switch 12 Auto switch Hs Hs RZQ 24.5 16 B 33 A B 26 A D-H7l, H7lW D-H7NF 20 to 63 D-C73C, C80C 20 to 63 8.5 Auto switch 8.5 Auto switch Hs Hs 16 16 B 29 A B 36.7 A D-H7C 20 to 63 D-B5, B6, B59W 20 to 100 12 Auto switch Hs 8.5 Auto switch Hs 24.5 16 B 38.2 A B 33 A (mm) Auto Switch Mounting Height Auto Switch
concurrent use of a CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
An auto switch cannot be mounted on the same side as a motor. Since the operating range is provided as a guideline including hysteresis, it cannot be guaranteed (assuming approx. 30% dispersion). It may change substantially depending on the ambient environment.
The above processes 1) and 2) are repeated at high speeds to establish the port A pressure. Circuit diagram The VY1D00, which is the smallest direct drive, consists of a solenoid, pressure sensor, control circuit, body cover, and a sub plate. The style with a sub plate can be used alone, and the style without a sub plate can also be used as a pilot valve.
The U-shaped groove is machined into the cushion ring in such a way that this acceleration process can proceed smoothly (as a sine function).
With shock absorber (16) MXS16BS, BT, B 19 A 10 37.5 37.5 18 18 55 (mm) Stroke adjustment range Retracting 5 10 20 20 15 20 20 20 A dimension (Retracted side mounting) Extending Model Shock absorber at retraction end Stroke 10 MXS16-10 MXS16-20 MXS16-30 MXS16-40 MXS16-50 MXS16-75 MXS16-100 MXS16-125 11 21 31 31 26 32 32 32 Shock absorber at extension end A Stroke 75 to 125 A Max. 25 Shock
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 8. Be aware that the stopping accuracy is influenced by changes in the piston speed.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder.
A Station 1 1 SOL. A Station 2 14 SOL. A Station 3 2 1 SOL. A Station 4 14 15 2 SOL. A 15 3 3 4 5 6 7 8 Station 5 16 17 18 19 20 SOL. B 16 SOL. A 4 Station 6 SOL. B 17 SOL.
coefficient of friction is greater than = 0.2, for reasons of safety, a gripping force should be selected which is at least 10 to 20 times greater than the work piece weight, as recommended by SMC.