Series DXT474 voltage may be slightly increased.
"'t I( r: i-: 1 \ W 'll f:: l '-'; I Q c...::; I ~"~ ...Ab.. ,..;= ~ -LK F N -H S + Stroke .!'!. FT ZZ1 +t+ Stroke Z Z t Stroke (mm) .. ,.,.,." .".
Therefore, if an air compressor has a small air delivery, the pressure may not be sufficient. Valve closed IDF FS Valve open IDFA IDFA IDFB IDH Auto Drain ID Caution IDG The auto drain may not function properly, depending on the quality of the compressed air. Check the operation once a day.
This product communicates by radio waves, and the communication may stop instantaneously due to ambient environments and operating methods. SMC will not be responsible for any secondary failure which may cause an accident or damage to other devices or equipment.
This product communicates by radio waves, and the communication may stop instantaneously due to ambient environments and operating methods. SMC will not be responsible for any secondary failure which may cause an accident or damage to other devices or equipment.
Note 3) Handling precautions: If drainage or oil, etc., enters the pressure gauge, an error may occur in the pressure gauge indication.
It may vary depending on connections.
(Assuming approximately 30% dispersion) There may be the case to change substantially depending on an ambient environment. D-X Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted.
(Heat sources should be blocked off, because radiated heat may cause damage due to softening of materials.) 1. Do not step on or place heavy objects on the unit. The equipment may be deformed or damaged, and if balance is lost, a fall may cause injury. 9 Series AMP Specific Product Precautions Mounting Supply Air Caution Caution 1.
(Heat sources should be blocked off, because radiated heat may cause damage due to softening of materials.) The equipment may be deformed or damaged, and if balance is lost, a fall may cause injury. 7 Series AMP Specific Product Precautions Be sure to read before handling. Refer to pages 5 through 7 for safety instructions and air cleaning equipment precautions.
It may not be possible to connect the tubing, or air leakage or disconnection may occur after connection. Release button Tubing Operating Environment Warning 1. Do not use in environments or locations where there is a danger of the speed controller being adversely affected. Refer to page 3 regarding speed controller materials. 2.
If any other lubricant is used, malfunction or other trouble may occur. Contact SMC regarding class 2 turbine oil (with additives) VG32.
CY1 MY1 If tightening the screw beyond the designated value, it may malfunction. If tightening it insufficiently, it may result in position sliding or falling off of air slide table. 3.11-3 Series MXS/Precautionsw Be sure to read before handing. Refer to p.0-39 to 0-43 for Safety Instructions and actuator precautions.
It may not be possible to connect them, or they may cause other trouble, such as air leakage or the tube pulling out after connection. Proper tightening torque (Nm) Male thread M5 10/32-UNF 1/6 turn after hand tightening 7 to 9 12 to 14 22 to 24 28 to 30 1/8 1/4 3/8 1/2 Precautions for One-Touch Fittings Caution Attaching and Detaching Tubes to One-Touch Fittings 1.
However, once lubrication is applied it must be continued, as the original lubricant may be eliminated leading to malfunction. Contact SMC regarding Class 2 turbine oil (with additives), ISO VG32.
If supply pressure to this regulator is interrupted while the power is still on, the internal solenoid valve will continue to operate and a humming noise may be generated. Since the life of the solenoid valve may be shortened by this, be sure to shut off the power supply when supply pressure is shut off. 5.
All 6ther options are available, whereas they may be stocked in lesser quantities or manufactured to order. Special arrangements can be made for repeating (blanket) orders of these product models.
The dither may generate vibrations in fe valve which produces a growling noise and may be ad.iusted within a range of 100 to 2m Hz by luming the DITHER adiustment screw.
SET POS. e Insert bushing G The tubing r may slip if there is oil or dust, etc., on the holder assembly y. Remove the contamination using alcohol or another suitable cleaner. Press the insert bushing e into the tubing r by turning the lever q.
If the current exceeds the specification failure may occ!r. Applicable model: D-A73, A73H, A73C, E7 3 A.Z7 3t D -97.93 A.