ZISE10.eng Pressure Setting In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function setting to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode. Measurement mode Press the button for 2 s or longer.
Product type 2. [P_1] and set value are displayed in turn. Displays in turn approx. 1 s Pin number Wire colour Mounting and Installation Switch output type 1 Brown (DC+) Troubleshooting approx. 1 s 2 N.C. CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: 3 Blue (DC-) Analogue output type Installation 3.
Alarm] [Software Reset] [ALM-CLR] ON Reset button Execute button FL-1*2 System Alarm FL-2*2 Alarm CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.
Alarm FL-2*2 CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.
(See the figure below) Measurement mode Press the button for 2 s or longer. In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode.
Specification NOTE The direct current power supply to be used should be UL approved as follows : Circuit (of class 2) which is of maximum 30Vrms (42.4V peak) or less, with UL 1310 class 2 power supply unit or UL 1585 class 2 transformer. The Pressure switch is a approved product only if it has a mark on the body.
Function selection mode Measurement mode Press the button for 2 s or longer Tube After maintenance is complete, perform appropriate functional inspections and leak tests. Stop operation if the equipment does not function properly or there is a leakage of fluid. When leakage occurs from parts other than the piping, the product might be faulty.
6) 7) 20 No.ZL3-OM00801-A 9. 9.1 ZL3 ZL3M ZL3H [mm] 1.9 1.5 [MPa] 0.35 0.50 *1 -91 -93 [MPa] 280 [L/min(ANR)] + *2 300 [L/min(ANR)] 150 135 [MPa] 0.20.6 [] -550() 2] *2 20 [m/s 2] *3 100 [m /s *1 *22 2/V *310500Hz XYZ 2 *4XYZ 3 ZL6 ZL6M ZL6H [mm] 1.9x2 1.5x2 0.35 0.50 [MPa] 0.37 0.52 *1 -91 -93 [MPa] 580 [L/min(ANR)] + *2 600 [L/min(ANR)] 300 270 [MPa] 0.20.6 [] -550() 2] *
X B(ZS-24-B) M45L B -16No.PS-OMM0006CN-E M8(3) (ZS-35-C/ZS-35-D) +(ZS-35-F/ZS-35-G) () ZS-35-C/D -17No.PS-OMM0006CN-E 79 Nm M5 (12mm) 1 2 1) 0.1 mm 2)0.1 mm 3)+0.15 mm -0.2 mm -18No.PS-OMM0006CN-E () TU0425 ( 4 2.5) -19No.PS-OMM0006CN-E (M8(3)22) Z/ISE40A--DC(+) -S/-R () NPN 2 Max.28 V80 mA 1 V R15 V 1 k S420 mA 12 V 300 24 V 600 50 OUT1 OUT2 DC(-) DC(+) -S/-R () NPN 2
Release ring How to Order Slide range 0P AS 0 06 06 20 Body size q qSlide down the release ring, and push the release bushing to the end.
Set the adapter with 2 set screws. Time [s] button (UP) button (SET) To obtain more detailed information about operating this product, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly. button (UP)
In measurement mode, press the S button for 2 seconds or longer, to display [F 0]. The [F ] indicates the mode for changing each Function Setting. Press the button for 2 seconds or longer in function selection mode to return to measurement mode. Displays the output status of OUT1 and OUT2. When the accumulated pulse output mode is selected, the output display will turn off.
Immediately after supplying power, there is drift of about 0.5% F .S. When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4.
SET for 2 s or longer Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 1. 1) OUT1 operation mode setting SET 1. 2) OUT1 output mode setting Troubleshooting Do not operate in an atmosphere containing flammable or explosive gases.
TMH Nil Option ASD None With seal Electroless nickel plated S N AS Type 1 If more than one option is required, write option part numbers in the order of S, N. 2 M3, M5, and U10/32 are not available with seals. AS-FE KE Elbow Universal 2 3 AS-FG Control type Applicable tubing O.D.
Seal Type: Metal, Configuration: 2-position, Number of Solenoids: Single, Voltage: 100VAC/50Hz, 115VAC/60HZ, Pilot: Pilot Exhaust through Footprint, Subplate: Side 3/8, Option: -
Seal Type: Metal, Configuration: 2-position, Number of Solenoids: Single, Voltage: 200VAC/50Hz, 230VAC/60Hz, Pilot: -, Subplate: -, Option: -
Seal Type: Metal, Configuration: 2-position, Number of Solenoids: Single, Voltage: 100VAC/50Hz, 115VAC/60HZ, Pilot: Pilot Exhaust through Footprint, Subplate: Side 1/4, Option: -
Seal Type: Metal, Configuration: 2-position, Number of Solenoids: Single, Voltage: 100VAC/50Hz, 115VAC/60HZ, Pilot: Pilot Exhaust through Footprint, Subplate: Side 1/2, Option: -
Seal Type: Metal, Configuration: 2-position, Number of Solenoids: Single, Voltage: 24VDC, Pilot: Pilot Exhaust through Footprint, Subplate: Side 1/2, Option: -