Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 20, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 20, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 30, Max.
Type: Lubricating Device, Type: Mixing valve, Material: Die-cast aluminum / Platinum silver coated, Rated Voltage: -, Air blow circuit: Yes, Float switch specifications: -, Nozzle tube: Flexible tubes, Nozzle tube length(mm): 300, Number of mixing valves used(pcs.): -
Type: Lubricating Device, Type: Mixing valve, Material: Die-cast aluminum / Platinum silver coated, Rated Voltage: -, Air blow circuit: None, Float switch specifications: -, Nozzle tube: Flexible tubes, Nozzle tube length(mm): 300, Number of mixing valves used(pcs.): -
Magnet: None, Mounting: B (Basic), Bore Size: 40mm, Thread Type: TN (NPT), Stroke: 30mm
Magnet: None, Mounting: Through-hole (Standard), Bore Size: 40mm, Port Thread: M thread: ø12 to ø32, Rc: ø50 to ø100, Stroke: 30mm
Plate Material: A (Aluminium Alloy), Bearing Type: L (Ball Bushing), Bore Size: 16mm, Port Thread Type: Rc (Or M5x0.8 for 12,16 Bore), Stroke: 30mm
Bearing: M (Slide Bearing), Bore Size: 25mm, Thread: TN (ø25,ø32 Bore: NPT 1/8), Stroke: 30mm
Magnet: None, Mounting: D (Double Clevis), Bore Size: 20mm, Port Thread: Rc: 32 to 100 Bore; M Thread: 20, 25 Bore), Stroke: 30mm
Accuracy: Basic Type, Size: 25, Bearing Type: L (Ball Bushing Bearing), Motor Mounting Position: D (In-line), Motor Type: NZ (Mounting Type Z), Lead Screw: B [LEYG25, 6mm; LEYG32, 8mm, (10)], Stroke: 30mm
Plate Material: A (Aluminium Alloy), Bearing Type: M (Slide Bearing), Bore Size: 50mm, Port Thread Type: TN (NPT), Stroke: 30mm
Size: 16, Bearing Type: L ( Ball Bushing Bearing), Motor Mounting: D (In-line Type), Motor Type: Step Motor (Servo/24VDC), Lead: C (Size 16: 2.5mm, Size 25: 3mm, Size 32/40: 4mm), Stroke: 30mm
EX260-SEN_eng X : Thread size: M3 x 30 The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.
Refer to page 30 for I/O memory map details. No. Item Meaning 1 IP Address IP address of SI unit connected to Web server Force output mode enable/disable.
Val: 1 to 65000 3 Valve ON/OFF counter (Counter) 8 Disable Does not generate an error. 1: This master is valid only when "Hold/Clear priority" of the system parameter is set to Handheld. : The count is memorized every 30 seconds per channel.
Valve diagnostics 2 . 5-5 Valve diagnostics 2 Bit 0 Valve 16, 17 diagnostics 01() 1 Valve 18, 19 diagnostics 01() 2 Valve 20, 21 diagnostics 01() 3 Valve 22, 23 diagnostics 01() 4 Valve 24, 25 diagnostics 01() 5 Valve 26, 27 diagnostics 01() 6 Valve 28, 29 diagnostics 01() 7 Valve 30, 31 diagnostics 01() 36 No.EX-OMU0020CN 5.1.2.
-SMC-EX260-.xml Tightening torque 0.6 Nm 2 EX260-SPN3/SPN4 : Thread size: M3 x 30 Output number assignment Output numbering starts at zero and refers to the solenoid position on the manifold. The following instructions must be followed during maintenance: Turn off the power supply.
Proper use of the seal cap enables the enclosure to achieve IP67 specification. : Refer to page 30 for the seal cap. -11No.EX-OMV0023-A Power supply connector layout PWR: M12 5-pin plug, A-coded (SPEEDCON) No.