There were no hits with the full part number, but there were 15 hits in the keyword search.
There were no hits with the full part number, but there were 10 hits in the keyword search.
Product Information » New Products Search Results
1 Manifold overall length Manifold overall length Approx. 29% reduced SY5000 manifold SY5000 3 stations SY3000 manifold SY3000 4 stations Mixed manifold SY5000 3 stations SY3000 4 stations For serial transmission EX260 A B A B A B A B A B A B A B A B A B A 14 A B A 14 A B A 14 A B A 14 A B A 14 A B A 14 Installation space A A A A A A A A B B B B B B B B 12 B 12 B 12 B 12 B 12 B 12 B 136.7 mm
set of a, b, c, d) BMA3-050 (A set of a, b, c, d) BMA3-063 (A set of a, b, c, d) CKQ D-M9ANote 2) BMA3-040S (A set of a, b, c, e) BMA3-050S (A set of a, b, c, e) BMA3-063S (A set of a, b, c, e) Auto switch Switch bracket (Resin) Transparent (Nylon)Note 1) d e White (PBT) c Switch holder b Auto switch mounting screw a * Band (a) is mounted so that the projected part is on the internal side
Magnet: Built-in, Mounting: Double Foot, Bore: 10mm, Stroke: 200mm, Head Cover: Perpendicular to Axis, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 0.5m Cord Length, M8-3 Pin Connector, Number: 2 pcs. (Or None in the Case of No Switch), Auto Switch Mounting: Rail Mounting, Cushion: Rubber
(Or None in the Case of No Switch), Auto Switch Mounting Type: A (Rail Mounting)
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
Due to a pressure fluctuation that occurs during the switching of the adsorption cylinders, the small particles of the adsorption agent could splash to the outlet side. Install a mist separator or a micro mist separator on the outlet side according to the application. 4. When installing a regulator, install it on the outlet side of the heatless air dryer.
Due to a pressure fluctuation that occurs during the switching of the adsorption cylinders, the small particles of the adsorption agent could splash to the outlet side. Install a mist separator or a micromist separator on the outlet side according to the application. 4. When installing a regulator, install it on the outlet side of the heatless air dryer.
ID-200Z ID-300Z ID-400Z ID-600Z 15.4 18.7 40.8 55.1 A B C inch mm inch mm inch mm 120 120 170 170 Operation Principles Provides dry air at dew point as low as 58F (50C).
This is a legacy product, and replaced byCDG1RN25-200Z CG/CG3 ROUND BODY CYLINDER. CYL, 25MM, DIR MT, AUTO-SW. ACTUATOR. 25MM CG DBL-ACT AUTO-SW. 1.52436 lb. IE.
This is a legacy product, and replaced byMB1B100-200Z MB TIE-ROD CYLINDER. CYL, TIE ROD. ACTUATOR. 100MM MB DOUBLE-ACTING. 15.60872 lb. SD.
This is a legacy product, and replaced byCDG1BN20-200Z-XB13, CYL, AIR, DBL ACT, LO SPEED, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, HC, 20MM CG OTHERS (COMBO), .66138 lb
This is a legacy product, and replaced byCY1SG15-200Z, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, GM, 15MM CY1S SLIDE BEARING, 3.31105 lb
This is a legacy product, and replaced byCY1SG32-200Z, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, LM, 32MM CY1S SLIDE BEARING, 11.07073 lb
This is a legacy product, and replaced byMGPM25-200Z-XC4AW, "COMPACT, MGP, GUIDED CYLINDER, N lb
This is a legacy product, and replaced byCM2KB20-200Z, CYL, ROUND BODY, NON ROTATING, ACTUATOR, CM2/CM3 ROUND BODY CYLINDER, HK, 20MM CM2 NON-ROTATING, 0.79425 lb
This is a legacy product, and replaced byCDG1TA50-200Z-B54L-XC4, CYL, AIR, DBL ACT, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, NE, 50MM CG DBL-ACT AUTO-SW, 5.41832 lb
This is a legacy product, and replaced byCDA2B40-200Z CA1/CA2 TIE-ROD CYLINDER. CYL, TIE ROD, NON LUBE,AUTO-SW. ACTUATOR. 40MM CA1 DBL-ACT AUTO-SW. 3.93152 lb. ME.