Your search for CQ2-Z returned 17 result(s)
There were no hits with the full part number, but there were 28 hits in the keyword search.
There were no hits with the full part number, but there were 5 hits in the keyword search.
Product Information » New Products Search Results
Compact Cylinder/Standard Type: Double Acting, Single Rod Series CQ2 Axial Mounting Lateral Mounting Body tapped Body through-hole Model Applicable bolt Max. tightening torque [Nm] Max. screw-in depth L [mm] Model Applicable bolt Max. tightening torque [Nm] Max. screw-in depth L [mm] Model Applicable bolt Max. tightening torque [Nm] MHL2-10DmZ M4 x 0.7 2.1 MHL2-16DmZ M5 x 0.8 4.3 MHL2-20DmZ M6 x 1 7.3 MHL2-25DmZ M8 x 1.25 17.7 MHL2-10DmZ M4 x 0.7 2.1 8 MHL2
NVHS2000 1/8, 1/4 1/8 40 56 36 28 22 25 NVHS3000 1/4, 3/8 1/4 53 74 45 48 28 30 NVHS4000 1/4, 3/8, 1/2 3/8 70 80 48 54 36 30 D I M E N S I O N S S E R I E S (N)VHS 3 P O R T VA LV E H O W T O O R D E R S E R I E S (N)VHS S H U TO F F V A LV E S (N)VHS 00 W I T H L O C K I N G FA C I L I T Y Standard N North American B O D Y S I Z E A N D A P P L I C A B L E FRL S E R I E S 2 2000 3 2500,
3 Series (N)VR1210-01 (N)VR1220-02 Ported Check Valve with one output and 2 pneumatic signal input ports Max Operating Pressure 1MPa / 145 PSI Min Operating Pressure 0.05MPa / 8 PSI Effective Orifice (Cv Factor) 7mm2(0.38) 15mm2(0.81) Port Size 1/8 PT / NPT 1/4 PT / NPT H O W T O O R D E R S H U T T L E V A LV E D I M E N S I O N S S H U T T L E V A LV E S Y M B O L S NVR1210-N01 (1/8 NPT
If the current pushing force exceeds the Trigger LV value of the step data, INP signal will turn ON. Note) If pushing operation is stopped when there is no pulse deviation, the moving part of the actuator may pulsate.
New Products Guide 1 Directional Control Valves Actuators Vacuum Equipment CAT.E00-6A INDEX New Products Guide 1 Directional Control Valves 5 Port Solenoid Valve Fieldbus System (For Input/Output) 2/3 Port Mechanical Valve Series SY3000/5000/7000 Series EX600 Series VM100/200 P .6 P .264 P .322 Actuators Foot Pedal Type 5 Port Mechanical Valve XT34-60/67 Air Cylinder Air Cylinder Series CJ2
When operated at a very low flow rate, the series LV with flow rate adjustment may vibrate, etc. depending on the operating conditions. Therefore, operate it after careful examination of the flow rate, pressure and piping conditions. 3. In the series LV, water hammering may occur depending on the fluid pressure conditions.
Trigger LV Setting is not required. Pushing speed Condition that turns on the INP output signal. The INP output signal is turned on when the generated force exceeds the value. Threshold level should be less than the pushing force. Max. torque during the positioning operation (No specific change is required.) Positioning force Trigger LV Condition that turns on the AREA output signal.
When [Pushing force] setting and [Trigger LV] are set less than [Pushing force], use the product within the specified range of [Pushing force] and [Trigger LV]. a) To ensure that the actuator pushes the workpiece with the set [Pushing force], it is recommended that the [Trigger LV] be set to the same value as the [Pushing force]. b) If the [Trigger LV] is set lower than the [operation pushing
Selection of Pushing Speed P Set the [Pushing force] and the [Trigger LV] within the range shown in the figure below.
Cylinder (Tube) Inner Diameter(φ): 50, Stroke(mm): 10, Cylinder Operation Method: [Double Acting] Double Acting, Rod Operation Method: Double rod, Main Body Shape: [Block Shape] Block shape, Additional Function: Standard, Environment, Applications: Standard, Operating Temperature(°C): -10～70, Operating Pressure(MPa): 0.05～1, Cushion: None, Specification: Without built-in magnet, Support bracket
Cylinder (Tube) Inner Diameter(φ): 50, Stroke(mm): 10, Cylinder Operation Method: [Double Acting] Double Acting, Rod Operation Method: Double rod, Main Body Shape: [Block Shape] Block shape, Additional Function: Standard, Environment, Applications: Standard, Operating Temperature(°C): -10～70, Operating Pressure(MPa): 0.05～1, Cushion: None, Specification: Without built-in magnet, Support bracket
Magnet: None, Mounting: B [Through Hole (Standard)], Type: Standard, Bore Size: 50mm, Port Thread Type: TN (NPT 32-100 Bore), Stroke: 10mm, Body Option: M (Rod End Male Thread), Auto Switch Groove: Z (Auto Switch Mounting Grooves)
D I M E N S I O N S S E R I E S (N)VHS S H U TO F F VA LV E S Y M B O L S Model Port Size Exh. Port A B C D E F Lockable Unit. Color may not be available as shown.
When operated at a very low flow rate, the series LV with flow rate adjustment may vibrate, etc. depending on the operating conditions. Therefore, operate it after careful examination of the flow rate, pressure and piping conditions. 3. In the series LV, water hammering may occur depending on the fluid pressure conditions.