SMC Corporation of America
Elite Part Number Search
Search Results "PSE304-MAC"

Software setting mode Hardware setting mode Software setting mode MAC ID: 0 MAC ID: 0 MAC ID: 63 Communication speed: 125 kbps Communication speed: 500 kbps Communication speed: 500 kbps The default output setting for when communication stops is 0 (all outputs to be cleared).

DeviceNet master malfunction Check the condition of the DeviceNet master. -29No.EX-OMN0013-I Fault No.6 Fault Probable cause Recommended error handling Recommended action Duplicate MAC ID Check the MAC ID is not duplicated with the other slave units. Set MAC ID to the SI unit correctly.

Setting of MAC ID Communication speed HOLD/CLR HW/SW mode (SW1) Setting of address is performed with SW1. MAC ID setting (Switch No.1 to 6) All setting are turned ON at shipment and the MAC ID is set to 63. Make sure to set the MAC ID in the range of 0 to 63.

Communication failure Check that there is no MAC ID duplication between the master and slaves. Set MAC ID correctly MAC ID duplication Confirm that the communication speed setting of the SI unit and the communication speed setting of the master and slave station are the same. Set the communication speed correctly. Check that there is no MAC ID duplication between the master and slaves.

The default setting is all switches ON, so the MAC ID is set to 63. The MAC ID should be set in the range of 0 to 63. 0: OFF 1: ON Switch No.

Main circuit Main circuit Main circuit Main circuit Load OUT1 OUT1 12 to 24 VDC 12 to 24 VDC Load (Black) (Black) OUT2 OUT2 Load Load (White) (White) Load Load DC() DC() (Blue) (Blue) PSE301 NPN open collector output (2 outputs), Max. 30 V or 80 mA, residual voltage 1 V or less Analog output: 4 to 20 mA Maximum load impedance: 300 (12 VDC), 600 (24 VDC) Minimum load impedance: 50 PSE304

Main circuit Main circuit Main circuit Main circuit Load OUT1 OUT1 12 to 24 VDC 12 to 24 VDC Load (Black) (Black) OUT2 OUT2 Load Load (White) (White) Load Load DC () DC () (Blue) (Blue) PSE301 NPN open collector output (2 outputs), Max. 30 V or 80 mA, residual voltage 1 V or less Analog output: 4 to 20 mA Maximum load impedance: 300 (12 VDC), 600 (24 VDC) Minimum load impedance: 50 PSE304

Main circuit Main circuit Main circuit Main circuit Load OUT1 OUT1 12 to 24 VDC 12 to 24 VDC Load (Black) (Black) OUT2 OUT2 Load Load (White) (White) Load Load DC () DC () (Blue) (Blue) PSE301 NPN open collector output (2 outputs), Max. 30 V or 80 mA, residual voltage 1 V or less Analog output: 4 to 20 mA Maximum load impedance: 300 (12 VDC), 600 (24 VDC) Minimum load impedance: 50 PSE304

The setting when shipped from plant is turned OFF, set to HW mode. 1 (No.1) 2 (No.2) 4 (No.3) 8 (No.4) 16 (No.5) 32 (No.6) MAC ID 0 OFF OFF OFF OFF OFF OFF No.10 Function Mode 1 ON OFF OFF OFF OFF OFF HW OFF Set MAC ID and baud rate with SW1 to 8. 2 3 OFF ON OFF OFF OFF OFF SW MAC ID and baud rate are set by network. : SW1 to 8 are ignored.

Doc no. LEC*-OMY0102-A NN32462501 PRODUCT NAME AC Servo Motor Driver (Network card type MODEL/ Series LECSN-T Series LECSN2-T Series / Driver 1. Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger. They are all important notes

Ethernet parameters Parameter name Set value Initial value Note MAC address MAC address of the product is displayed. Select the IP address setting mode. Select the mode suitable for your network environment. Manual: The IP address is set by inputting it directly. DHCP: The IP address is set automatically via the DHCP server.

Available Available MAC address MAC address of the Wireless Base unit Available Available IP address IP address of the Wireless Base unit Available Not available Subnet mask Subnet mask of Wireless Base unit Available Not available Module in/out size Number of occupied points for the control input and output of the Wireless Base unit.

Description Explanation MAC address MAC address of the product is displayed. Select the IP address setting mode. Select the mode suitable for your network environment. IP address setting mode Manual: The IP address is set by inputing it directly. BOOTP/DHCP: The IP address is set automatically via the DHCP server. IP address Sets the IP address.

Description Explanation MAC address MAC address of the product is displayed. Select the IP address setting mode. Select the mode suitable for your network environment. IP address setting mode Manual: The IP address is set by inputing it directly. BOOTP/DHCP: The IP address is set automatically via the DHCP server. IP address Sets the IP address.

Select SI unit MAC address for assigning IP address. -33No.EX-OMT0009 (6)[Edit Ethernet Node] will be displayed with GW unit MAC address.