HRX-OM-W002

For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.

HRX-OM-Y098

This value is not measured by a flowmeter. It should be used as a reference value (rough indication).

Thermo-chiller

Use this as a reference.

AC Servo Motor Driver (SSCNET Type)

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

CNG

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

Rotary Actuator/Vane Type

The maximum dimension L1 is, as a rule, twice the thread size.

7

MK Note) A knuckle pin, cotter pins and flat washers are provided as a standard for Y.

Stopper Cylinder

Set the operating pressure using the graphs shown on the right as a guide.

Series PF2W Digital Flow Switch For Water

Especially avoid the application of pressure through a water hammer, which is above the specification. a) Use a device such as a water hammer relief valve to slow the valves closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 8.

New

Note) Use this graph as a guide.

Fieldbus System

Provide a specific grounding as close to the unit as possible to minimize the distance to grounding. 0 V 0 V Power supply for control/input 24 V Power supply for control/input +24 V 4. Do not install a unit in a place where it can be used as a foothold. Applying any excessive load such as stepping on the unit by mistake or placing a foot on it, will cause it to break. 5.

5 Port Air Operated Valve

AXT620-32-1 (M4 x 48, With spring washer) For mounting valve M4: 1.4 Nm 1509 VFA3000/5000 Series Dimensions: VFA3000 Series/Base Mounted 2 position single VFA3140(-P) 02 03 2 position double VFA3240(-P) 02 03 28 33 28 33 1/4, 3/8 [4 (A), 2 (B) port] 1/4, 3/8 [4 (A), 2 (B) port] 13 13 22 22 1/8 (Pilot port: Upward) 81 1/8 (Pilot port: Upward) 46 20 36 36 20 46 4A 2B 4A 2B 26.4 26.4 35 42

Direct Solenoid

Should the valve require dis3mbly for maintenenos lhe Spool and Sleeve should be rstalnd as a unit. TULTI.PURPOSE FLOW PATTEN : True mulli.purpos valves. Any port may be pressurlzed, backpressured, or plugg8d without 8ftcllng ths spool acflon. Normally usd as a singfs lolet A-way to conttol double ac ng cylinders. May also !

VQ5000

Type Series VQ5000 Dimensions (mm) 1in 25.4mm Bottom port diagram With connector on U side (FU) 106 46.8 59.2 83.5 9 9 55.5 M5 ground screw 2n-1/2 (ports A, B) 34.5 n U side X 12 B 2 A 4 6 B A B 2 A 4 5 SMC SMC SMC SMC SMC B A B 2 A 4 4 B A P=41 L1 L2 B 2 A 4 3 B A B 2 A 4 2 B A 34.5 46 68.5 P = 41 A 4 B 2 1 B A 58.5 X 12 Stations 2-1/8 (external pilot port) 15.5 22 51 69 117 42 16 107.8

Solid State Auto Switches

If conditions (water splashes, time, temperature) beyond the normal ranges can be applied to the auto switch, use the auto switch in an environment where it will not be directly exposed to water splashes at a high temperature by installing a cover to protect the entire auto switch, as long as it is possible.

MY2

If driving a load such as a relay that generates a surge voltage, use a contact protection box. Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly.

MGZ Series

It is again necessary to connect a contact protection box in order to extend its life. Please contact SMC in this case. If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

Title not found

With the expansion of its international network, SMC has earned a solid reputation as reliable international brand, and has exceeded the goal of 20% global market share.

ARM10/11

Do not apply a tensile force to a cord. To connect the switch body and the contact protection box, connect the lead wire of the contact protection box on the side marked with SWITCH and the lead wire from the switch body. Connect the switch body and the contact protection box with a lead wire of 1 m or shorter and arrange them as close as possible.

ARM10/11

Do not apply a tensile force to a cord. To connect the switch body and the contact protection box, connect the lead wire of the contact protection box on the side marked with SWITCH and the lead wire from the switch body. Connect the switch body and the contact protection box with a lead wire of 1 m or shorter and arrange them as close as possible.