MU These are installed with double clevis style and double knuckle joint style as standard. 2.4-17 Plate Cylinder Series MU Accessory Dimensions Single Knuckle Joint Double Knuckle Joint (mm) (mm) Applicable pin Model MUl25 MUl32 MUl40 MUl50 MUl63 Z LX RR 8.5 10 11 16 16 LD LU 11 14 15 20 20 LC 16 18 20 28 28 LB 27 31 36 46 46 Z LA 35.5 41 47 62 62 LX RR 8 10 10 16 16 LB 27 31 36 46 46 L 52.5
SI unit of the SDTC or SDTD specification to an input block or valve.
Do not use the cylinder under the following environments: An area in which fluids such as cutting oil splash on the piston rod An area in which foreign matter such as particles, cutting chips, or dust is present An area in which the ambient temperature exceeds the operating range An area exposed to direct sunlight An environment that poses the risk of corrosion 2.
Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder. Compact lock unit is light weight and saves space Overall length has been reduced by using an independent brake cylinder (15% compared to P/A products).
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 1. Be certain to connect the rod end to the load with the lock released.
Note 11) For an actuator with lock, add the power consumption for the lock.
If the allowable value is exceeded, an external cushioning mechanism such as an absorber needs to be installed. P. 305 Checking allowable load 5 M = 0.4 x 9.8 x 0.05 + 0.2 x 9.8 x 0.1 = 0.392 [Nm] If the allowable value is exceeded, an external bearing needs to be installed. Check if the load applied to the product is within the allowable range.
Also, BBA2 is included when an auto switch alone is shipped.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Also, BBA2 is included when an auto switch alone is shipped.
On the other hand, in ordinary counters, no. 1 is set to 9.98 and no. 2 is set to 10.06, and if no. 1 is ON and no. 2 is OFF, an acceptance decision is made. 2 points of output are used in order to check whether or not the product is within dimension tolerances. In this example, one preset of the CEU5 performs the same function as two presets of an ordinary counter.
On the other hand, in ordinary counters, no. 1 is set to 9.98 and no. 2 is set to 10.06, and if no. 1 is ON and no. 2 is OFF, an acceptance decision is made. 2 points of output are used in order to check whether or not the product is within dimension tolerances. In this example, one preset of the CEU5 performs the same function as two presets of an ordinary counter.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 46 3/8" 24 52 28 23 21 44 1/2" M 55 1/2" H 29 62.5 39 32 26 53.5 3/4" 72 3/4" 25 1 39.5 81 49 46 36 71 1" Class 6 Inch sizes (A) shows the reference dimension after connection.
Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
For mounting D-A9(V), M9(V), M9W(V), M9A(V) with 32 to 50 to a surface other than the port surface, order an auto switch mounting bracket separately.
This can cause a loss of repeatability when gripping workpieces and have an adverse effect on the life of the unit.
This can cause a loss of repeatability when gripping workpieces and have an adverse effect on the life of the unit.
Panel mount adapter (Part No.: ZS-46-B) Panel mount adapter + Front protective cover (Part No.: ZS-46-D) Switch output specifications Diagnostic information PNP Panel ALL : One arbitrary display mode can be added to the sub display by setting the [F10] sub display.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.