Basic Type/Direct Mount Type

Reference values for non-rotating accuracy and maximum allowable moment at stroke end are indicated below.

IDU/IDF

IDU3D to 75C Max. ambient temperature 40C Page 23 IDF1D to 75C Max. operating pressure 1.0MPa Max. operating temperature 60C Bypass piping set Easy bypass piping (connect this set to the air dryer), realizing substantial reduction of man-hours at the site.

Direct Operated Pilot Operated 2-Port Solenoid Valve Refer to pages 7, 9, 11, 25, 35, and 39 for details.

While maintaining the upstream pressure at a fixed value above 0.3 MPa, measure the max. flow to be saturated initially. Next, measure this flow rate at 80%, 60%, 40%, and 20%, as well as the upstream and downstream pressure. The sonic conductance C can be calculated based on this max. flow rate.

Conforming to ISO Standard Solenoid Valve (with M12 Connector) Series EVS7-6/7-8/7-10 (Size 1) (Size 2) (Size 3) 1

Note 2) Use dry air to prevent dew condensation when operating at low temperature. Note 3) Subject to JIS B 8375-1975.

MK

Note 4) At 0.5 MPa.

3 Port Solenoid Valve, VQZ Series, Base Mounted and Body Ported

Refer to each manifold dimensions for L dimension. 25 35 5.5 To order a manifold with DIN rail already attached, insert "D" at the end of the manifold part number. The DIN rail is approximately 30mm longer than the length of manifold. 1.25 L dimension L=12.5n+10.5 35.5 1 23 No.

Speed Controller with Uni One-touch Fitting AS Series Push-lock type

To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.

Series CG1-Z 10-/11- ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 21-/22- Air Cylinder: Double acting, Single rod

Auto Switch Proper Mounting Position (Detection at Stroke End) (mm) Auto Switch Mounting Height (mm) D-M9l D-M9lW D-M9lA D-A9l Hs 20 26.5 25 29 32 32.5 40 37 50 42.5 63 49.5 D-M9l D-M9lW D-M9lA D-A9l Auto switch model Auto switch model Bore size A B A B 20 12 24 8 20 25 11.5 24.5 7.5 20.5 32 13 25 9 21 40 18 27 14 23 50 20 32 16 28 63 18.5 33.5 14.5 29.5 Bore size Note) Adjust the auto switch

3 Port Solenoid Valve Metal Seal/Rubber Seal, Base Mounted Series VQZ100/200/300 21

Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.

Magnetically Coupled Rodless Cylinder Low Profile Guide Type Series CY1F ø10, ø15, ø25 1

Maximum load mass MTS 2 = M/Mmax Review M1, M2, M3 Mmax is the allowable moment at a L1 2. Static moment MY 3 = ME/MEmax Review M1E, M2E, M3E MEmax is the allowable moment at a CY 3.

Magnetically Coupled Rodless Cylinder Low Profile Guide Type Series CY1F ø10, ø15, ø25 1

The mounting hole at the center of the guide body is used to mount an intermediate support. Be sure to use the 4 mounting holes at both ends to secure the product.

4-channel Flow Monitor ( compatible)

(page 72) Y U16 0x0064 5 R/W (100) Setting of OUT1 delay time at ON. 0x0 ~ 0x1770 (0 ~ 6000) 0.01 s increment dtH1 (OUT1 delay time at ON) Y U16 0x0 6 R/W (0) dtL1 (OUT1 delay time at OFF) Setting of OUT1 delay time at OFF. 0x0 ~ 0x1770 (0 ~ 6000) 0.01 s increment Y U16 0x0 7 R/W (0) OUT1 Accumulated threshold value setting (L) Consider the accumulated inclination when reading or writing

10

An auto switch can be mounted at 4 locations.

Series SYJ500 Rubber seal 3 Port Pilot Solenoid Valve

. 300 (Lead wire length) Pg7 65.5 [67.7] 75.5 55.7 [57.9] 64.6 57.2 50.7 34.7 8 9 8 9 8 9 8 9 14.5 3 14.5 3 14.5 3 14.5 3 20 20 20 20 23 23 23 23 27 Refer to the page 68 for dimensions with connector cable. 19 Series SYJ500 Base Mounted (With Sub-plate) [ ] for AC Grommet (G), (H): SYJ54G H -01 1/8 (A port) 18 8.5 2-4.5 (For mounting) 4 34 Manual override A 24 P R 33.5 G: Approx. 300 H:

Tie-rod Type Hydraulic Cylinder

H B C F A E G J K L D Size Tolerance +0.027 0 +0.027 0 +0.027 0 +0.027 0 +0.033 0 +0.033 0 +0.033 0 40 47 21 45 19 12 9 18 12 32 M8 x 20 60 R15 40 double clevis type 44 L K counter bore depth 2 J counter bore 50 53 23 50 23 12 11 21 14 35 M10 x 22 73 R18 50 double clevis type 53 A B 63 60 27 55 23 15 11 23 16 40 M10 x 25 80 R20 63 double clevis type 60 AC-A1bore size 80 67 31 65 28 16 13

Industrial Filters

30 19.5 23 30 FGC Internal volume (L) 27 43 52 27 43 52 FGF Note 1) Cannot be used with gases.

JIS Standard Hydraulic Cylinder Series CH2E/CH2F/CH2G/CH2H

When a cylinder is nearly at rest, the relation of generated force, bore size and pressure can be expressed with the following formulas.

Round Type Low Pressure Hydraulic Cylinder Series CH
M

When operating a cylinder for the first time, be sure to release the air at low pressure. When the air release is complete, operate the cylinder at reduced pressure, then gradually increase it to the normal operating pressure. However, the piston speed at this time should be adjusted to the minimum speed.

Brake mechanism added

Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? YES YES When positioning at the outside of the allowable range, do you have any problem in doing a trial once again? NO NO There is no particular problem in using thesystem.

Plug-in Unit

rated voltage) None Insulation Short circuit protection Operates at 1A Typ.