Free Mount Cylinder Series CU Actuator driving system Inside of clean room w t e q r t q Cylinder relief port piping w Solenoid valve exhaust piping e Breathing piping of regulator r Drain piping t Exhaust Cleaner for Clean room/AMP series Cylinder relief port piping Series 10-/12-/21(atmospheric release type) Connect the relief port piping with the dedicated duct piping installed outside the clean room or with the exhaust
e t t y w w e e q q q 1 port 2 port 1 port 2 port 1 port 2 port r r r !
H H 15 Indicator light (Red, Green) 23 Indicator light (Red, Green) 23 600 (3000) 56.5 600 (3000) 49 8.5 47 47 3.5 3.5 8.5 2-3.5 Mounting hole T1: NPTF 1/8 01: R 1/8 M5 x 0.8 depth 5 Piping port M5 x 0.8 depth 5 Piping port 2-3.5 Mounting hole T1: NPTF 1/8 01: R 1/8 13 13 16-6-5
1 SET1 SET2 L L H H 15 SET1 SET2 L L H H 15 Indicator light (Red, Green) 23 Indicator light (Red, Green) 23 600 (3000) 56.5 600 (3000) 49 8.5 47 47 3.5 3.5 8.5 M5 x 0.8 depth 5 Piping port 2 x 3.5 Mounting hole T1: NPTF 1/8 01: R 1/8 M5 x 0.8 depth 5 Piping port 2 x 3.5 Mounting hole T1: NPTF 1/8 01: R 1/8 13 13 777
Port size With One-touch fitting 01 M5 M5 R 1/8 R 1/4 R 3/8 R 1/2 02 03 04 Needle Valve/Flow Rate Characteristics Note) The flow rate characteristics are representative values.
0 r t !1 y q e u o w i !3 !2 w Auto switch *No spacer !2 for Z type Parts List Repair Parts: Standard Seal Kit for Double Acting, Single Rod Remarks Description Material No.
Install the ejector body gasket for manifold t into the gasket groove of each vacuum pump system assembly r. 2. Install the ejector body gasket for manifold t into the gasket groove of the end block R w. 3. Align the ejector assemblies r, end block (L) w, and end block (R) e using positioning pins (at the two a positions) and fasten with clamp rods q (2 pcs.)
Cable wire color Terminal 1 Brown DC+ q 2 Not used N.C. w 3 Blue DC e 4 White IN: 1 to 5 V r Power supply / Output connector (8P) Power supply / Output connector (accessory) i u y t r e w q Pin no. Pin no. Terminal 7 Green CH4_OUT1 8 Yellow N.C.
The needle will fall out if it is turned more than 4 full turns. 1 Connector (w/o lead wire) LO Without connector M Connector (0.3 m) MN Connector (w/o lead wire) MO Without connector G Grommet (0.3 m) H Grommet (0.6 m) 3 100 VAC 110 VAC 5 24 VDC 6 12 VDC V Pilot valve DC: 0.45 W (With indicator light: 0.5 W) AC DC: 1 W (With indicator light: 1.05 W) Nil 6 VDC S 5 VDC R 3 VDC Applicable
Interface Speed Controls Cylinder speed can be controlled by throttling exhaust air. 20 Comforming to ISO 15407-2 Series VSR/VSS8-4 How to Order Manifold (ISO15407-2) 03 SDQ VV8 01 N 1 1 N 5 W1 Option Note 1) Size Nil None 01 Size 01 Special wiring specifications (Except double wiring) K Number of stations External pilot R 1 1 station Direct exhaust with built in silencer S 16 16 stations
1 Drain q r e w t i u y o !0 !
r e Pressure gauge unit 2) 1) Refer to gauge guide (P.94) for gauge specifications. w q w q w q Unit psig/bar MPa Code No code MPA Sample Order Number Port AZ1001S e q FV4 FV4 FV4 w FV4 FV4 FV4 r 2PW 3PW 4PW 2PW 3PW 4PW 2) Pressure gauge unit MPa or psig/bar selectable.
VQ1000-FPG-C4M5-D: 6 sets Double check block 757 S0700 Series Construction Body Ported Construction 2(B) (A)4 S0716 2-Position Single r u e w q 3(R2) (R1)5 1 (P) t y i 2-Position Double S0726 2(B) (A)4 r u e w q 3(R2) (R1)5 1 (P) t y i 3-Position Closed Center S0736 r u e w q 2(B) (A)4 (R1)5 1 (P) 3(R2) t y i 4-Position Dual 3-Port Valve S07A6 r u e w q 2(B) 4(A) 5(R1) 3(R2) 1(P) N.C. + N.C
A Cooling capacity Note 4) The cooling capacity reduces about 300 W from the value in the catalog.
R. Unit/Specifications Air filter (w/auto-drain, w/manual drain) 5m Filtration Regulator 0.05 to 0.85MPa Set press.
Configuration 1 master : 1 thermo-chiller 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-11 Connection of RS-232C 3.3 Installation HRS Series 3-16 HRX-OM-R005 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.