VEX-OMY0001 ) a,b 12(P1),23(P2) (2) a 12(P1) 1(P)2(A)3 3(R) 3(R) b 23(P2) 2(A) 2(A)3(R)1 1(P) 1(P) 12(P1) 1 2 3 23(P2) 4 5 6 7 8 POM 9 -12No.VEX-OMY0001 () () 3(R) 2(A) 1(P) 1(P) 2(A) 3(R) () a b P1P2 2(A) 1(P) -13No.VEX-OMY0001 (7) (1) (2) (3) (4) (5) (6) (12) (7) (8) () (9) (5) (6) (14) (10) (P2) (5) (4) (11) (4) (13) DCAC (7) 14 No.VEX-OMY0001 o. (1)
Remove the gauge and balance the bridge circuit (P1 = P2) by adjusting the variable orifice (S3) via the adjustment knob. By moving the work piece away from the nozzle (S4) a pressure differential (P1 P2) is created. As soon as the work piece is moved within the detection range of the AirCatch Sensor the back pressure P2 increases.
OFF OFF OFF OFF P1 n1 P2 P1 n2 n1 (Standard: Factory setting) (Reversed) (Standard: Factory setting) (Reversed) Press the SET button to set the mode and proceed to the output type setting. 3 2-Color Display Type High-Precision Digital Pressure Switch Series ZSE30/ISE30 Pressure setting Auto preset setting Manual setting Press the SET button in the measuring mode to display the set value.
Note 4) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above).
One of the preset pressures P1 through P4 is selected by the ON/OFF combination of S1 and S2.
= Inlet pressure) (P2 = Outlet pressure) Inlet pressure P1 (MPa) R A Flow rate (/min (ANR)) P A Inlet pressure: 0.3 MPa Outlet pressure (MPa) Set point Set point Outlet pressure (MPa) Inlet pressure P1 (MPa) Outlet pressure (MPa) Set point Set point R A Flow rate (/min (ANR)) P A Inlet pressure P1 (MPa) 14-9-14 5 Electro-pneumatic Proportional Valve Series VEF/VEP Construction Flow type
When the work piece comes close to the detection nozzle, the back pressure P2 increases until it is larger than P1 (P2 > P1). Then the switch output turns on to notify that the pressure is below the detection gap.
OFF OFF OFF OFF P1 n1 P2 P1 n2 n1 (Standard: Factory setting) (Reversed) (Standard: Factory setting) (Reversed) Press the SET button to set the mode and proceed to the output type setting. 16-2-6 7 Series ZSE30/ISE30 High Precision, 2-color Display Digital Pressure Switch Pressure setting Auto preset setting Manual setting Press the SET button in the measuring mode to display the set value
How to Find the Flow Rate (at air temperature of 20C) Subsonic flow when P1 + 0.1013 < 1.89 (P2 + 0.1013) Q = 226S P(P2 + 0.1013) Sonic flow when P1 + 0.1013 1.89 (P2 + 0.1013) Q = 113S (P1 + 0.1013) Q: Air flow rate [l/min (ANR)] S: Effective area (mm) P: Differential pressure (P1P2) [MPa] P1: Upstream pressure [MPa] P2: Downstream pressure [MPa] Correction for different air temperatures
How to Find the Flow Rate (at air temperature of 20C) Subsonic flow when P1 + 0.1013 < 1.89 (P2 + 0.1013) Q = 226S P(P2 + 0.1013) Sonic flow when P1 + 0.1013 1.89 (P2 + 0.1013) Q = 113S (P1 + 0.1013) Q: Air flow rate [l/min (ANR)] S: Effective area [mm] P: Pressure drop rate (P1P2) [MPa] P1: Upstream pressure [MPa] P2: Downstream pressure [MPa] Correction for different air temperatures
18 C 6 +0.030 0 depth 2.5 2.5 Width across flats 6 E 5 6 5 Prepared hole diameter 3.3 2 x M4 x 0.7 Piping port 2 x M3 x 0.5 (Plug: M-3P) F QL 6 13.5 17 Stroke: S M 2 0.05 M4 x 0.7 Mounting base side B D 7 5 2 x M3 x 0.5 Piping port Y J 3 M3 x 0.5 Vacuum suction port Z Max. 9.5 (Rubber stopper) 2.4 3.5 depth 2 2.5 +0.030 0 7 +0.030 0 depth 2 2.5 Q QL Without magnet and switch rail 2 2 x M2
Find the inertial moment B for the rotation of shaft (B). 3 + m2 a22 + K (Example) When shape of m2 is a sphere, refer to 7, and K = m2 2r2 2.
For encoder connector Screw size: M2 Tightening torque: 0.1 N m For brake connector Screw size: M2 Tightening torque: 0.2 N m For power supply connector Screw size: M2 Tightening torque: 0.2 N m -16- 4.4 Handling Warning 1. Do not touch the motor during operation. The surface temperature of the motor can increase to approx. 80C due to operating conditions.
For encoder connector Screw size: M2 Tightening torque: 0.1 N m 2.4 Handling For brake connector Screw size: M2 Tightening torque: 0.2 N m For power supply connector Screw size: M2 Tightening torque: 0.2 N m Warning 1. Do not touch the motor during operation. The surface temperature of the motor can increase to approx. 80C due to operating conditions.
x 0.4 depth 2.2 12 Metal stopper 11-/22-MXP6-10 Max. 10.5 F 4-M3 x 0.5 depth 3 12 2-M2 x 0.4 depth 3 (mm) E F H J M Q QL S W Y Z AA Model 23 25 38 33.5 37 28 8 5 42 22 45 2 11-/22-MXP6-51 30 35 42 48.5 47 37 11 10 53 27.5 60 9.5 11-/22-MXP6-10 101 Air slide table MXP/MXPJ6 11221122Dimensions: MXP10 2-M3 x 0.5 depth 5 Z 3 Metal stopper V K C 4 5 C Max. 5.5 20 G Without stroke adjuster N M
Static Load) 40 1 2 Ek= m2 Bore size 1000 Holding force (N) 32 500 25 20 60 40 50 0 0.1 0.2 0.3 0.4 0.5 Load weight (kg) 40 Air pressure to pressurized lock port (MPa) 32 Cautions when Locking Caution 40 30 25 20 32 The holding force is the lock's ability to hold a static load that does not involve vibrations or impacts, when it is locked without a load.
Referring to case u where "W2" is a sphere, 4a +b 2 2 2 4a +b 2 1 2 1=m1 +m2 12 12 2 r K=m2 5 2 tThin rectangle board (Parallelogram) !0Gear transmission Position of rotation axis: Passes through center of gravity and perpendicular to the board. (Same formula regardless of board thickness.) 1. Find moment of inertia1B around the rod (B). 2.
Mounting thread is also reinforced from size M1.7 to M2.
Find the inertial moment B for the rotation of shaft (B). 3 + m2 a22 + K (Example) When shape of m2 is a sphere, refer to 7, and K = m2 2r2 2.