Trimmer Auto Switch Use a wire 3 m or shorter between the sensor and amplifier. If the sensor cable length exceeds 3 m, the CE marking does not apply to the auto switch. Although wire length of power supply/output cable should not affect switch function, use a wire 100 m or shorter. 3. Take precautions for the internal voltage drop of the switch.
Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) J79CN Besides the models in the above table, there are some other auto switches that are applicable. For more information, refer to page 861. Refer to pages 1784 and 1785 for the details of auto switches with a pre-wired connector.
Plate A Plug (M-3P) (2 pcs.)
(example: If the pressure switch with output impedance of 1k is connected to the A/D converter to detect the analog output of 5V, the detected voltage by the A/D converter becomes 5(V) x 1(M)/(1(k) + 1(M)) 4.995(V), and there is an error of approximate 0.005 V). Output impedance The operation principle of the switch output. Normal output and reverse output can be selected.
-11041 IFETEL:xxx-xxx H 26043 IFETEL: RCPSMEX21-1677 Mexico Brazil Argentina UK Europe Ukraine TA-2021-0088 AGREE PAR L'ANRT MAROC Numro dagrment : MR00027841ANRT2021 Date dagrment : 19/03/2021 APPROVED South Africa Morocco HIDF18000274 Australia Singapore Malaysia B2100197 SMC Indonesia Vietnam CCAH21LP1360T1 Taiwan Authorized by the Ministry of International Affairs and Communications R-R-OZK-NT1
[F 2] Wiring LED display [A ir ] dry air, N2 [F 3] [FLU] Operating fluid [r EF] Reference condition [eES] Response time Wiring of connector Connections should only be made with the power supply turned off. Use separate routes for the product wiring and any power or high voltage wiring. Otherwise, malfunction may result due to noise.
Safety cannot be assured in the case of unexpected malfunction. [ PoS] Orientation [ Hor ] Horizontal mounting [F31] [ Pr S] Supply pressure [ m id] 0.4 MPa minimum, 0.6 MPa maximum Connector pin numbers (lead wire) The accumulated flow has reached the set accumulated flow value.
AL7 T h e r m o s t a t (0.1C) 0.0 Sets lower limit of temp measured by the internal temp sensor and stops operation of the product. 0.0 to 59.0C A H Do not make any modification to the product. Do not disassemble the product, unless required by installation 11 Ambient temperature is too high. (out of 10-35oC) Correct the ambient temperature within the specification range.
Apr R QR RR SR . ZR AR BR . Jul U QU RU SU . ZU AU BU . Month Q R S . Z A B . Oct X QX RX SX . ZX AX BX . T With stand for vertical installation 8 1 15 9 D-sub 15 pin (Socket type) Fixed screw: M2.6 Description No.
connector Connector Z None Standard Stroke Range of manufacturable stroke Standard stroke (mm) Tube Bore(mm) Without Gaiter With Gaiter Without Gaiter With Gaiter 40 25850 25700 1200 950 50 25800 25650 1150 900 63 25800 25650 1150 900 80 25750 25600 1100 900 4-2 Controller 100 25750 25600 1100 850 CEU2 Output Method None NPN Open Collector P PNP Open Collector 16 4-3 Extension Cable CE1-R
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be as 3% or less of the rated voltage. 3.
A filtration degree of 5 m or less should be selected. Install an air dryer, after cooler or Drain Catch(water separator), etc. Air that includes excessive drainage may cause malfunction of valves and other pneumatic equipments. To prevent this, install an air dryer, after-cooler, or water separator, etc.
If a current of more than 3.1 A can not be avoided, supply the power to the Power block and SI unit (solenoid valve manifold) by separate cables. -53No.EX-OMH0025-C (2)EX500 series for use with Output block Details of EX500 series suitable for use with the Output block. : Only VQC series solenoid valve is applicable. (3)End plate (Intput side) (4)End plate R (Output side) Details of the end
Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be 3% or less of the rated voltage. 7.
CJ1 CJP CJ2 CM2 C85 Component Parts CG1 No. q w e r t y No. u i o !0 !1 !
2 r!4 i yq !3t!8!1!7w !6ui e!5 CJ1 CJP CJ2 CM2 C85 !
port thread type Series 3 SYA3000 5 SYA5000 Nil Rc G F 40 SYA 7 1 Base mounted N NPT NPTF T P, R port thread type Type of actuation Nil Rc 2 position single G F Port size 1 N NPT Symbol Applicable series Nil Port size Without sub-plate NPTF T 2 position double 1 8 01 SYA3000 Port size With sub-plate 2 Symbol Nil Port size Without sub-plate Without sub-plate (Pilot port: Expect RC) 1 4 With
Fitting Type: H (Connector), Metric Size, Side A: No (Select Inch Size, Side A), Inch Size, Side A: 5E (Tube O.D. 3/4", Tubing Size 3/8"x1/4"), Metric Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Inch Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Piping: M (Male)
Fitting Type: H (Connector), Metric Size, Side A: 4F (Tube O.D. 1/2", Tubing Size mm 3x2), Inch Size, Side A: No (Select Metric Size, Side A), Metric Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Inch Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Piping: M (Male)
Fitting Type: H (Connector), Metric Size, Side A: No (Select Inch Size, Side A), Inch Size, Side A: 5F (Tube O.D. 3/4", Tubing Size 1/4"x5/32"), Metric Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Inch Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Piping: M (Male)