AXTS-OMY0007 2.5 Hz 3.2 Hz 3.6 Hz 4.4 Hz 0 2 4 6 8 7 Number of rotation of OFF adjustment needle 24% 58% 69% 67% ON At an inlet pressure of 0.3MPa.
Switch No. 0 (Default) 1 2 3 4 5 6 7 8 9 Slower (Speeds up gradually.)
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. 1 ( 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
Rotation angle rad Inertia moment kgm For equiangular acceleration, the angular velocity, , after t seconds are obtained using the following equations. ) 1 ( ) 2 ( C : Integration constant Because the displacement angle in t=0 becomes =0, it becomes C=0.
0.88 6 3 +0.02 0 6 M(D)HR3-15 9 !
WaitTime_Setting int 500 WaitTime setting after valve operation (Unit: ms, Range: 0..1000ms) It is a wait time value after the valve for opening gripper is energized. Set an appropriate value according to the opening speed of the gripper by adjusting the opening of the metering valve.
Set value Alarm type Operation profile 0 No alarm 3 Upper limit of the * Even if PV is in the alarm triggering range when power is supplied, the alarms above do not generate an alarm immediately.
Locations where ambient temperature is beyond following range: On-stream: 2 ~ 40oC Storage: 0 ~ 50oC (when there is no drain water inside of the piping) Locations where temperature changes rapidly.
(Figure b) : Bit status "0" and "1" on a data corresponds solenoid valve status ON and OFF (0: OFF, 1: ON), and output number starts at zero from LSB (least significant bit). -15No.EX-OMO0007-E Troubleshooting and Maintenance Troubleshooting Chart Applicable SI unit: EX180-SMJ3/5 When any malfunction is observed, perform the following troubleshooting.
100-DCN709SN Part Numbers P398020-501-3 P398020-500-3 Input Type 0 ~ 10V 0 ~ 10V 4 ~ 20mA 4 ~ 20mA Bore 25mm 40mm 25mm 40mm Stroke 50mm 100mm 50mm 100mm Type Straight type M12 connector Right angle type M12 connector Working Principle Linear displacement sensor gives feedback signal to controller.
(N specifications) How to Order AS4200-04 AS3200-03 01 S AS 2 2 0 0 AS2200-02 AS2200-01 Option Body size AS1200-M5 None With seal Nil 1 2 3 4 M3, M5 standard S K N 1 8 1 4 , standard standard standard AS1400-M3 Hexagonal lock nut 8 3 Electroless nickel plated 2 1 If more than one option is required, write option part numbers in the order of S, K, N.
Refer to p.0-26 and 0-27 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.1.0-1 and 1.0-2 for precautions on every series. Selection Warning qThe residual secondary pressure cannot be released by releasing the supply pressure. To release the residual pressure, contact SMC.
Dew point conversion chart 60 50 40 30 Pressure dew point C 20 10 1.5MPa 1.3MPa 1.1MPa 0.9MPa 0.7MPa 0.5MPa 0.3MPa 0.1MPa Atmospheric pressure 0 10 20 30 40 50 60 50 60 40 30 20 10 0 10 20 30 Atmospheric pressure dew point C 25 Series IDU/IDF Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
x 3 x 60 = 2736g/h. 6 7 8 3 1 2 3 4 5 Dew point conversion chart 60 50 40 30 Pressure dew point C 20 10 1.5MPa 1.3MPa 1.1MPa 0.9MPa 0.7MPa 0.5MPa 0.3MPa 0.1MPa Atmospheric pressure 0 -40 -30 -20 -10 -60 -50 -60 -50 -40 -30 -20 -10 0 10 20 30 Atmospheric pressure dew point C 8 Series IDUS/IDFS Safety Instructions These safety instructions are intended to prevent a hazardous situation and/
0 !1 !2 !3 !8 !9 @0 @1 @2 @3 D-9 Hard anodized Oil impregnated Oil-impregnated sintered alloy High carbon chrome bearing steel High carbon chrome bearing steel Carbon tool steel Carbon steel Phosphate coated 8-3-9 10 Series MXU Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A9 D-M9 D-F9W ( ): Denotes the values of D-A93.
Fluid Air/Inert gas 0 to 1.0 MPa Operating pressure range SY Proof pressure 1.5 MPa 20 to 60C (No freezing) Ambient and fluid temperature SYJ Any given port can accept high or low pressure supply without affecting the system life or operation. No-lubrication and dry-air operation possible. Response time (1) 10 ms or less (AC), 45 ms or less (DC) 1,500 c.p.m. (AC), 180 c.p.m.
Ambient and fluid temperature (C) 0 to 60 Lubrication (1) Required (Use turbine oil Class 1 ISO VG32.) Mounting orientation Free Impact/Vibration resistance (m/s2) (2) 150/50 Note 1) Use turbine oil Class 1 (ISO VG32).