This is a legacy product. Please contact us for the latest version.sales@ocaire.com, SWITCH ASSEMBLY, INSTRUMENTATION, ISE30/ISE30A PRESSURE SWITCH, 1X, ISE30 OTHER SIZE RATING, .22046 lb, ModelRated pressure rangeSet pressure rangeWithstand pressureMinimum unit settingApplicable fluidPower supply voltageCurrent consumptionSwitch output--RepeatabilityHystere- sisAnalog outputDisplayDisplay
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, SWITCH ASSEMBLY, INSTRUMENTATION, ISE30/ISE30A PRESSURE SWITCH, 1X, ISE30 OTHER SIZE RATING, .08157 lb, ModelRated pressure rangeSet pressure rangeWithstand pressureMinimum unit settingApplicable fluidPower supply voltageCurrent consumptionSwitch output--RepeatabilityHystere- sisAnalog outputDisplayDisplay
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, SWITCH ASSEMBLY, INSTRUMENTATION, ISE30/ISE30A PRESSURE SWITCH, CA, ISE30 1/8 INCH PT VERSION, .28292 lb, ModelRated pressure rangeSet pressure rangeWithstand pressureMinimum unit settingApplicable fluidPower supply voltageCurrent consumptionSwitch output--RepeatabilityHystere- sisAnalog outputDisplayDisplay
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, SWITCH ASSEMBLY, INSTRUMENTATION, ISE30/ISE30A PRESSURE SWITCH, 1X, ISE30 OTHER SIZE RATING, .34506 lb, ModelRated pressure rangeSet pressure rangeWithstand pressureMinimum unit settingApplicable fluidPower supply voltageCurrent consumptionSwitch output--RepeatabilityHystere- sisAnalog outputDisplayDisplay
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, OTHER NO SIZE RATING, VACUUM SERIES, ZSE30 VACUUM SWITCH, 2X, OTHER NO SIZE RATING, 0.13227 lb
PF3A7xxH-L.eng PF3A706H PF3A703H Equivalent to M4 1.5 Nm10% 8 7 Peak display Bottom display OUT2 hysteresis Equivalent to M5 3 Nm10% The following instructions must be followed during maintenance: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance work Otherwise an injury can result.
Item Default setting PF3W7##-L Lock ring Without units selection function Display OUT1 set value OUT1 hysteresis OUT2 hysteresis Bottom value OUT2 set value Peak value [ Unit] Display unit setting [ L] L/min, oC Bracket mounting (PF3W711) Mount the product (with bracket) using the mounting screws supplied (M5 x 4 pcs.).
The tightening torque must be 1 to 1.2 Nm. 2 4 Safety Instructions 4 OUT1 (C/Q) How to reset the product after a power cut or when the power has been unexpectedly removed The settings of the product are retained from before the power cut or de-energizing.
M5 After tightening by hand, tighten additional 1/6 to 1/4 rotation with a tightening tool Tapered thread for Rc port (MGP) and NPT port (MGPTN) Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it.
Solid sphere Position of rotational axis: Through the center of diameter r 2 2 r I = m5 27 - Kinetic energy Table 9 shows the allowable kinetic energy of the rotary table.
Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be 3% or less of the rated voltage. 7.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. DC coil 3% or less of the rated voltage 6.
Solid sphere Position of rotational axis: Through the center of diameter 2 2 r I = m5 27 - Kinetic energy Table (9) shows the allowable kinetic energy of the rotary actuator. The end angular speed is obtained by: Table 9.
Bore size (mm) 32 40, 50, 63 80, 100 Thread size M2.5 X 0.45 X 25 l M3 X 0.5 X 30 l M5 X 0.8 X 40 l Pulling force 4.9N 10N 24.5N Stroke (mm) 2 3 3 e Release lock when mounting or adjusting the cylinder. If mounting is done with lock engaged, lock mechanism may be damaged. * Remove bolt under normal operations.
Snap ring Spring steel Aluminum alloy 6 18 Anodized End plate Rod seal NBR Aluminum alloy 7 19 Hard chrome plated Non-rotating rod Piston seal NBR Stainless steel 8 20 Bushing O-ring A NBR Resin 9 21 Bushing (for non-rotating rod) O-ring B NBR Lead-bronze casting 10 22 Bumper O-ring C NBR Urethane rubber 11 23 Nickel plated Electroless nickel plated Reinforcement ring Hexagon socket head
Turn the oven ON when the temperature reaches 110 degrees C and OFF when the temperature reaches 125 degrees C. Alternate: Alternate turning your output device "ON" and "OFF" from the same Input. Real Time Clock (RTC): The Y2K compliant RTC can control up to 160 time/date combinations. Simply set your outputs to function daily, weekly, monthly or set operations by a calendar date.
Series ZMA How to Order ZMA 07 1 H K 5 T14 C Nozzle diameter Switch lead wires (connector type) 0.5mm 0.7mm 1.0mm 1.3mm 1.5mm 05 07 10 13 15 Lead wire length 0.6m Lead wire length 3m Without lead wires C CL CN Switch type Body type Without 1 point setting/analog output 3 rotations, NPN output T14 For single type Common SUP for manifold Individual SUP for manifold 1 3 5 Without 1 point setting
Guide type C Cam follower guide Number of auto switches Bore size 16 25 40 16 mm 25 mm 40 mm 2 pcs. 1 pc. n pcs. Nil S n Auto switch Thread type Nil Without auto switch (Built-in magnet) Refer to the table below for the applicable auto switch model.
Rotary Cylinder Series MRQ Size: 32, 40 How to Order 32 MRQ B S 50 C A J79W Made to Order or port type Refer to page 343 for the Made to Order details. Nil XF Rc 1/8 G 1/8 NPT 1/8 XN The combination with Made to Order is not available.
ow 0.2 0.3 0.4 0.2 0.2 0.3 0.1 0.2 0.1 0.2 C and b values are for controlled ow with the needle fully open and free ow with the needle fully closed.