Speed Controller with Indicator Stainless Steel Type Elbow Type/Universal Type AS-FSG Series Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
auto switch when mounting a housing of 10.
B 89 A A B Section BB Coupling P.C.D.
an element is incorporated into a vessel.
Furthermore, since valves and cylinders are not guaranteed for zero air leakage, it may not be possible to hold a stopped position for an extended period of time. Contact SMC in case it is necessary to hold a stopped position for an extended period. Caution 1. Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting.
Common supply bushing 136144-S Individual supply bushing 136144-K Single unit regulator / Port plug for regulator block 136144-S 136144-K Option A-A A Nil X17 None A-A A Oil-free 12 12 10 A A 8 8 15 15 10 14-4-38 21 Regulator Single Unit Type Series ARM10 How to Order F.R.L. ARM10 06 B Z 1 AV AU 1 2 3 4 1.
Common supply bushing 136144-S Individual supply bushing 136144-K Single unit regulator / Port plug for regulator block 136144-S 136144-K Option A-A A Nil X17 None A-A A Oil-free 12 12 10 A A 8 8 15 15 10 14-4-38 21 Regulator Single Unit Type Series ARM10 How to Order F.R.L. ARM10 06 B Z 1 AV AU 1 2 3 4 1.
Accessory None (Standard) With bracket (Except IDG1) Nil B Note) When symbol B is indicated, a bracket assembly with a part number shown in the table below is included as an accessory.
When using a cylinder with long strokes, implement an intermediate support. When using a cylinder with long strokes, implement an intermediate support to prevent the tube from sagging and being deflected by vibration or an external load. Refer to the Guide to Side Support Application on page 1195. 2. For intermediate stops, use a dual-side pressure control circuit.
Do not use in an atmosphere of corrosive gases, chemicals, sea water, water or water vapor or in an environment where such substances may adhere. 2. Provide shading in an environment where the product is exposed to the sunlight. 3. Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem.
ideal throttle without friction deduced from the calculation of the pressure changes inside an air tank or without reduced flow when discharging the compressed air in a choked flow, from an equipment attached to the air tank.
After some resistance is felt, use a wrench that matches the wrench flats of the hexagon portion to tighten it an additional 1/4 turn.
A Work load [kg] Work load [kg] LEJ LEJ 40 Lead 20: LEJS63A Lead 16: LEJS40A Lead 30: LEJS63H 30 Lead 24: LEJS40H LEL A 20 A LEM 10 A A 0 LEY 0 200 400 600 800 1000 1200 1400 1600 1800 0 200 400 600 800 1000 1200 1400 1600 1800 Speed [mm/s] Speed [mm/s] LES Vertical Vertical LEPY LEPS 10 20 Lead 10: LEJS63B Lead 8: LEJS40B A Area where the regeneration option is required.
Do not operate the cylinder if there is the risk of scratching or gouging the piston rod, such as by contact with a sharp section on a pallet, as this could cause malfunction. eUsing a stopper cylinder to act as an intermediate stop for a load that is connected directly to a cylinder, etc.: The operating range given in the catalog is applicable only for stopping the pallets on a conveyor.
Do not weld an arm to the cylinder. 4) Always use a speed controller, and set it so that it takes at least 1 second from unclamped to clamped, and at least 1 second from clamped to unclamped. 5) This product is designed to be used after being adjusted using a shim.
When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube to an unnecessary degree. Accepts nylon, soft nylon and polyurethane tubes. Has high retaining force. Packing Tube Can be used for a wide range of pressure from a low vacuum up to a pressure of 145psi {1.0MPa }.
Do not install the gauge in an area that is exposed to high temperatures or humidity. 4. When attaching the pressure gauge, make sure to place a wrench directly on the squared off portion. If a force is applied to some other area to screw in the gauge, it could cause the gauge to leak or to become damaged. C Note) X3 (wetted parts) is not stainless steel specifications.
Please contact SMC for a specification sheet when placing an order.
For slou/er cyde rates and intermittent duty, consult factory) iiOUNTIiIG: Inlended for loot mounting or are llght enough to hang in a pipe line May be mounted in any posllion. 140. F (60p c) 11v50 a 12U60 115" F (46"C) MULII.PURPOSE FLOW PATTEBN: True multi-purpose valv.