Guide Table Series MGF The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
Origin Home Switch Infotmation LX series actuators are available with an optional photo micro sensor as an origin home switch to detect when the actuator is fully retracted. The LCOC seies positioning drjver requires an input from the origin home switch or some other sensor when homing the actuator.
Please See Below for How to Order Seal Kit 14* Rod Seal NBR Available only as an Assembled Item. Please See Below for How to Order Seal Kit 15* Piston Seal NBR Available only as an Assembled Item. Please See Below for How to Order Seal Kit 16* Cushion Valve Seal NBR Available only as an Assembled Item.
The I/O map is shown with the following unit configuration as an example.
Since no protective cover is installed on the product, provide an external protective cover protecting the entire product wherever possible. Using the product in an environment where it is exposed to water, liquid coolant or dust such as iron powder will cause an adverse effect to the ball screw and the guide. Therefore, an external cover is also required for dust prevention. 8.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. 4. Keep wiring as short as possible.
Attachment should be designed as light and short as possible. 1. Long and heavy attachment increases the inertia force to open or close the fingers. It may cause unsteady movement of fingers and have an adverse effect on life. 2. Even if holding point remains within the limited range, make the attachment as light and short as possible. 1.
Contact P/A when using the regulator between a solenoid valve and an actuator.
Also, BBA2 is included when an auto switch alone is shipped.
Avoid sudden temperature changes even within specified ambient temperature range, as it may cause condensation. 2. Do not use this product in an enclosed space. This product utilizes a corona discharge phenomenon. Do not use the product in an enclosed space as ozone and nitrogen oxides exist in such places, even though in marginal quantities. 3.
the model to process an air flow larger than 412 l/min IDF11C is selected as the model to process an air flow larger than 1400 l/min (ANR) with a 60Hz power supply, according to data D-2.
Note 2) Operate an interface regulator only by applying pressure from the P port of the base, except when using it as a reverse pressure valve. When using it as a reverse pressure valve, P port regulation is not allowed to use. Note 3) When using a perfect spacer, assemble a valve, a spacer regulator and a perfect spacer in this order to use it.
(Ex.: 2504-N002) Construction/Parts/Dimensions AN103 AN203 Construction/Parts/Dimensions VEX AN AMC AN303/403 AN200 to 900SAN, #1 to #8 AN202 to 402SAN, #9 to #11 AN103 to 403SAN, #12 to #15 5.2-2 ANm00/ANm02/ANm03/25/AN (BC Sintered Body) Series AN Ideal for the exhaust of a compact valve or pilot air.
Within the reciprocating movement of the actuator, if only the movement in one direction must be controlled, connect an airhydro unit to the cylinder piping port of the control direction as shown in Fig. (1).
Within the reciprocating movement of the actuator, if only the movement in one direction must be controlled, connect an air-hydro unit to the cylinder piping port of the control direction as shown in Fig. (1).
Furthermore, it cannot be used as an emergency cutoff valve.
(s P. 11 ) (2) The weight of a transferred object and transfer speed should be within the allowable range as shown in the graphs. (3) Overhang L3 should be 30 mm or less. V m L3 30 mm Caution (1) If a load is applied in the direction as shown on the right side, an eccentric load will be applied to the guide.