A_HEC-OM-J017 SMC Corporation R&D Center Product Development Division-6 Address: 4-2-2, KINUNODAI,TSUKUBAMIRAI-CITY , IBARAKI-KEN 300-2493, JAPAN Phone:+81-297-52-6 Fax:+81-297-20-5007 E-mail:kaihatsu_6_g3@smcjpn.co.jp Notice: The content of this manual can be revised without a previous notice.
Switch No. 0 (Default) 1 2 3 4 5 6 7 8 9 Slower (Speeds up gradually.)
Description Number Note 6 Nameplate 1 1 Rack 1 Anodized 7 Rotation display plate 1 2 Slider 2 Black 8 Tube gasket Slider O-ring 2 Zinc Chromated 3 Spring pin 4 4 Connecting screw 2 Zinc Chromated 9 Bearing 2 11 Piston seal 2 Black dye 5 Piston 2 Chromated 12 Hexagon socket set screw 8 Black dye 13 Spring washer 8 Black dye 14 Round head phillips screw 4 20 - Basic circuit for using rotary
Stroke (mm) Refer to the standard stroke table on page 2.
(HFC) IDFA55E 390 432 510 R 2 IDFA75E 660 720 822 2.
Offset 3: Power supply connector Supplies power to the solenoid valve, the Output block, SI unit and the Input block. 2 30 28 26 24 22 16 0 4 6 4 2 0 6 20 18 4 2 0 4 0 4 0 Input No. Bit No.
Possible causes Countermeasures 2 Air leaks from the One-touch fitting. 2-1) Tube is not inserted all the way into the fitting. 2-2) Tube has a gouge 2-3) The cut surface of the tube is slanted. Check all possible causes and make sure the piping is correct. Replace the part, if necessary. 2-4) One-touch fitting seal is damaged Replace One-touch fitting assembly 3.
Plate A Plug (M-3P) (2 pcs.)
As a guide, insert bolts in 2 locations for 2-5 stations, 3 locations for 6-10 stations, 4 locations for 11-15 stations, 5 locations for 16-20 stations and 6 locations for 21-24 stations. Caution 2. When using the manifold with DIN rail in an environment where any vibration or impact is applied to it, the DIN rail itself may be broken.
Possible causes Countermeasures 2 Air leaks from the One-touch fitting. 2-1) Tube is not inserted all the way into the fitting. 2-2) Tube has a gouge 2-3) The cut surface of the tube is slanted. Check all possible causes and make sure the piping is correct. Replace the part, if necessary. 2-4) One-touch fitting seal is damaged Replace One-touch fitting assembly 3.
flow rate (l/min) EJ101S-004 4 70 x 250 EJ101S-006 6 2 EJ101S-013 13 4 20 6 Note) Specity seal material in place of "" (N for NBR or V for FPM).
M10 x 1 Piping port 2-M5 x 0.8 Cover side (rear side) 5 8 6 20 M5 x 0.8 20.3 25 23 14 2.3 9 6 33 21 0 -0.3 18.3 9.5 42 15 55.5 + Stroke 28 83.5 + Stroke 2-5.5 Mounting hole With rear end lock / CBJ2L16-HN Piping port 2-M5 x 0.8 6 8 8 Cover side (front side) 2-M10 x 1 5 20 M5 x 0.8 19.8 23 25 14 2.3 9 6 33 0 -0.3 18.3 12.5 12.5 15 42 28 8 50 + Stroke 86 + Stroke 2-5.5 Mounting hole 5 Series
Note 2) The plug-in type is only available with 5 (24VDC) and 6 (12VDC).
<> [F 2] ON OFF OFF ON ON [F 2] OUT2 1 2 2 3ON(H_4)OFF(H_2) 25 - [F 3] <> [F 3] , [F 3] 26 - [F 4] <> [F 4] , [F 4] , (28 -) ,ON/OFF 27 - OUT1 , AP1 OUT1 OUT1 OUT1 A1L A1H P_1H_1 (n_1H_1) P_1=A-(A-B)/4 A= H_1=|(A-B)/2| B= 1 28 - [F 6] 5R.D. <> [F 6] [FSC] 1 [F 6] 29 - [F11] <> [F11] , 1000 100 [F11] [MPa]/[kPa]/[kgf/cm 2]/[bar]/[psi]/[inHg] 2]/[bar]/[psi]/
through K 40 3.5 100 120 114 8.7 6-K (6 places) 57 114 5 Guide Table Series MGF 63 MGF63 Scale: 40% 4-M10 x 1.5 through 140 160 120 11.5 48.5 + Stroke 10 60 + Stroke 20 9 2-Rc 1/4 port for extending cylinder Breathing hole for guide (with element) When the cylinder is extended 46 Port for retracting cylinder 4-M10 x 1.5 through M6: T-slot for hexagon bolt K 50 140 160 146 4 11 6-K (6 places
Allowable load mass mv (kg) Maximum operating pressure Pv (MPa) Cushion Stroke Model Stroke (mm) 25 30 1 5 0.3 Model CYP15 CYP32 CYP15 CYP32 8-17-6 6 Clean Room Rodless Cylinder Series CYP 15, 32 How to Order MX CYP 15 Z73 200 MTS MY Number of auto switches Nil S n 2 pcs. 1 pc. n pcs.
(Refer to pages 15-6-3 to 15-6-5 for details.) ASP ASN Model Applicable tubing O.D.
Parameter Default ( ) 6. 6. Clear Error Log -32No.EX-OML0010CN-C 4. Parameter Setting() 2. [4.Parameter Setting] Waring 1. 3. 4. 1. 34 2. 34 3. 35 4. 41 -33No.EX-OML0010CN-C 1. a) b) c) d) 2.