AC Servo Motor Driver (CC-Link Type) An error code is returned if an instruction code outside the range set in parameter No.
An error code is returned if an instruction code outside the range set in parameter No.
PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
An environment where food which will be sold as merchandize, directly touches the fitting components. Installable Splash zone An environment where food which will not be sold as merchandize, directly touches the fitting components. An environment where there is no contact with food.
Cylinder speed < Counting speed of the counter (Cylinder speed 500 mm/sec = Counting speed of the counter 5 kcps) RS Q G RS H A RZQ MI W S Example of Recommended Pneumatic CEP1 Horizontal mounting Vertical flat mounting Vertical overhead mounting CE1 W W CE2 ML2B C J G5-S CV MVGQ Note) In the case of light load, regulate head side supply pressure.
Mitsubishi Electric Corporation Yaskawa Electric Corporation Nil W G 1 N.C. (B contact) 2 pcs.
Max.allowable load W max. : Table 2 1=W/Wa 3-2 Load rate of static moment M=W(Ln+An)/1000 Corrected value for center position distance of moment An : Table 3 Ma=M max. Allowable moment coefficient : Graph 2 Max.allowable moment M max. : Table 4 Calculate static moment M(Nm). Examine for Mr [As Mp and My does not arise, Examination is not needed.]
Without brake C section Brake electric circuit YellowC;*1 Y e l l o w O Y !
Install an emergency stop circuit. Install an emergency stop outside of the enclosure so that the system operation can be stopped immediately and the power supply disconnected. 4.
OO PP QQ RR SS TT UU VV Model Applicable gasket ML1C25 ML1C32 ML1C40 10 14 37 24 8 27 20 8 C11.2 16.5 18 46 30 12 32 22 8 C11.2 17 23.5 12.5 10 53 40 34 26 C14 A B C D E F G H I J K L M N O P Q R S T U V W Y Z Model ML1C25 ML1C32 ML1C40 274 260 137 140 88 108 87 85.5 60 74 97 100 42.5 26 34 206 28 24 5.6 9 5.5 M5 x 0.8 8.5 M6 x 1 9.5 11 M8 x 1.25 322 306 161 160 108 131 101 99.5 64 92 118
When mounting an auto switch (3) Tube top mounting (When mounting an auto switch into the groove from the top before holding the product) (When mounting an auto switch into the groove from the top after installation) Auto Switch Proper Mounting Position [mm] Auto switch model Bore size D-M9, D-M9W D-M9V, D-M9WV D-M9A D-M9AV A B W A B W A B W A B W 12 6.2 6.2 3.8 6.2 6.2 1.8 6.2 6.2 5.8
Vertical mounting: f = W = 0.3 (Slide bearing) = 0.1 (Ball bushing bearing) W 0.5 NO Confirmation of adjusting bolt capacity W WA Determine the movable weight WA which can be operated only by adjusting bolts.
I T C H E S Reed D-90 (DC Only) D-97 (w/LED, DC Only) A-90A (AC or DC) D-93A (w/LED, AC or DC) Solid State D-F9N (W/LED, 3 Wire NPN) D-F9P (W/LED, 3 Wire PNP) D-F9B (W/LED, 2 Wire) N O O F S W I T C H E S 2 Switches S 1Switch Safety Note For cap type mounting, care should be taken not to exceed 6 bar when ejecting the workpiece Courtesy of Steven Engineering, Inc. !
With air cushion 15 LH B 4 x LD Z Y X W LZ LX 2 x LC (Knock pin position) ZZ + S Stroke LS + Stroke Y X W M (mm) B 54.5 78 LS 54 LX 71 LZ 4 M 10 W 4 LC 7 LD 30 LH 3 LT 16.5 X 8.5 Y Z 63.5 205 ZZ Bore size 40 50 63 5 5 10 12 40 45 91 91 4.5 4.5 17.5 17.5 70.5 75.5 66 82 86 106 5 5 22 22 11 13 242 242 82.5 75.5 Other dimensions are the same as basic type.
W -X 20W Data Mounting Caution 1. Be sure to connect the load to the rod end with the cylinder in an unlocked condition.
A cabtire cable with an O.D. 6 to 12 mm is applicable. Tighten each part with an appropriate tightening torque shown below.
(Using outside of the operating limit may give an adverse effect on the service life such as looseness in the guide unit and a loss of precision.) RS Q G RS H A RZQ MI W S 5. Take care not to scratch or gouge the sliding portion of the rod. This may cause a malfunction or shorten the units life. CEP1 CE1 6.
3 w q e RE A B REC CX CY !5 !0 !1 !2 u y i o MQQ M RHC MK(2) Material Note Component Parts RS Q G No. q w e r t y u i o !0 !1 !2 !3 !4 !5 !
Rod end thread type is an optional product. (Refer to page 281).
A contact protection box is not required for solid state auto switches due to their construction. q Where the operation load is an inductive load. w Where the wiring length to load is greater than 5 m. e Where the load voltage is 100 VAC.